In this study, the effect of porogenic solvents on pore size distribution of the polycaprolactone (PCL) thin films was investigated. Five thin PCL films were prepared using the solvent-casting method. Chloroform, Methylene Chloride (MC) and three different compositions of MC/ Dimethylformamide (DMF) (80/20, 50/50 and 20/80) were used as solvents. Scanning Electron Microscopy (SEM) investigations were employed to study morphology and consequently the pore size distribution of the prepared films. The PCL films made by chloroform and MC as a solvent were completely non-porous. Whereas the other films (made by a combination of MC and DMF) showed both uni-modal and bi-modal pore size distributions.

This report deals synthesis of CuInGa (CIG) nano materials along with doctor blade and spin coated thin films selenization and their physical properties. The doctor blade and spin coated CIGS/SLG thin films thicknesses are obtained ̴ 2 μm and ̴ 2.95 μm.  Raman spectroscopy of these thin films leads the chalcopyrite phase formation by exhibiting the peak at wave number 171 cm^-1. The well developed grain growths of spin coated thin film are appeared in the surface morphology. While the grain growths developments in doctoral blade coated thin film is rather hard and fuzzy. EDS measurement recognised the existence of the compositional ratio presence of the alloying elements Cu, In. Ga and Se. The doctor blade and spin coated CIGS/SLG thin films are exhibited the UV- Visible transmission peak in the wave length range 240 nm 320 nm. The optical energy band gaps for the doctor blade and spin coated CIGS thin films are obtained 1.41eV and 1.5 eV.        

Regarding to the influence of chloride and fluoride ions on the corrosion resistance, the electrochemical behavior of Ti alloys has been deeply studied. In this work, the main goal was to investigate the electrochemical behavior of cp-Ti and Ti-Mo alloys containing 6, 10 and 15 wt% of Mo concentrations. All the samples were immersed in different solutions, such as 0.15 mol L^-1 Na₂SO₄, 0.15 mol L^-1 Ringer, 0.15 mol L^-1 Ringer plus 0.036 mol L^-1 NaF and 0.036 mol L^-1 NaF. Simulating the commercial fluorinated gels, the NaF solutions naturally-aerated were prepared with 1450 ppm of fluoride ions. The electrochemical techniques applied in this work were the open-circuit potential, cyclic voltammetry, besides the technique for chemical identification, which was X-ray photoelectron spectroscopy. The formation and growth of TiO₂ and MoO₂ were identified, without pitting corrosion. The electrochemical stability and the corrosion resistance of the Ti-Mo alloys decreased in the solutions containing chloride and fluoride ions, with an appreciative decrease especially in the fluorinated medium. The Ti-Mo alloy with higher Mo content concentration was the material with higher corrosion resistance. Therefore, it is a promising candidate as a biomaterial, once the osseointegration needs a satisfactory corrosion resistance for being achieved.

ZrO₂ thin film samples were produced by the sol-gel dip coating method. Four different absorbed dose levels (such as ~ 0.4, 0.7, 1.2 and 2.7 Gray-Gy) were applied to ZrO₂ thin films. Hence, the absorbed dose of ZrO₂ thin film was examined as physical dose quantity representing the mean energy imparted to the thin film per unit mass by gamma radiation. Modification of the grain size was performed sensitively by the application of the absorbed dose to the ZrO₂ thin film. Therefore the grain size reached from ~50 nm to 87 nm at the irradiated ZrO₂ thin film. The relationship of the grain size, the contact angle, and the refractive index of the irradiated ZrO₂ thin film was investigated as being an important technical concern. The irradiation process was performed in a hot cell by using a certified solid gamma ray source with 0.018021 Ci as an alternative technique to minimize the utilization of extra toxicological chemical solution. Antireflection and hydrophilic properties of the irradiated ZrO₂ thin film were slightly improved by the modification of the grain size. The details on the optical and structural properties of the ZrO₂ thin film were examined to obtain the optimum high refractive index, self-cleaning and anti-reflective properties.

In this study, robust and defect-free thin film composite (TFC) forward osmosis (FO) membranes have been successfully fabricated using ceramic hollow fibers as the substrate. Polydopamine (PDA) coating under controlled conditions is effective in reducing the surface pores of the substrate and making the substrate smooth enough for interfacial polymerization. The pure water permeability (A), solute permeability (B), and structural parameter (S) of the resultant FO membrane are 0.854 L·m^–2·h⁻¹·bar⁻¹ (LMH/Bar), 0.186 L·m^–2·h⁻¹ (LMH), and 1720 µm, respectively. The water flux and reverse draw solute flux are measured using NaCl and proprietary ferric sodium citrate (FeNaCA) draw solutions at low and high osmotic pressure ranges. As the osmotic pressure increases, a higher water flux is obtained, but its increase is not directly proportional to the increase in the osmotic pressure. At the membrane surface, the effect of dilutive concentration polarization is much less serious for FeNaCA-draw solutions. At an osmotic pressure of 89.6 bar, the developed TFC membrane generates water fluxes of 11.5 and 30.0 LMH using NaCl and synthesized FeNaCA draw solutions. The corresponding reverse draw solute flux is 7.0 g·m^–2·h⁻¹ (gMH) for NaCl draw solution, but it is not detectable for FeNaCA draw solution. This means that the developed TFC FO membranes are defect-free and their surface pores are at the molecular level. The performance of the developed TFC FO membranes is also demonstrated for the enrichment of BSA protein.