Four alloys based on niobium and containing about 33wt.%Cr, 0.4wt.C and, in atomic content equivalent to the carbon one, Ta, Ti, Hf or Zr, were elaborated by classical foundry under inert atmosphere. Their as-cast microstructures were characterized by X-ray diffraction, electron microscopy, energy dispersion spectrometry and while their room temperature hardness was specified by Vickers indentation. The microstructures are in the four cases composed of a dendritic Nb-based solid solution and of an interdendritic NbCr₂ Laves phase. Despite the MC-former behavior of Ta, Ti, Hf and Zr usually observed in nickel or cobalt-based alloys, none of the four alloys contain MC carbides. Carbon is essentially visible as graphite flakes. These alloys are brittle at room temperature and hard to machine. Indentation shows that the Vickers hardness is very high, close to 1000HV_10kg. Indentation lead to crack propagation through the niobium phase and the Laves areas. Obviously no niobium-based alloys microstructurally similar to high performance MC-strengthened nickel-based and cobalt-based can be expected. However the high temperature mechanical and chemical properties of these alloys remain to be investigated.

The present study demonstrates the effect of direct solar drying (DSD) and hot air drying (HAD) on the quality attributes of Fuji apple slices. DSD samples took a longer time (150–180 min) to dry and simultaneously reached higher equilibrium moisture content at the end of rehydration than HAD samples. DSD samples have higher rehydration ability, dry matter holding capacity, and water absorption capacity than HAD samples. Among several empirical models, the Weibull model is the best fit with higher R² (0.9977), lower root mean square (0.0029), and chi-square error (0.0031) for describing the rehydration kinetics. Rehydrated HAD samples showed better color characteristics than DSD in terms of overall color change, chroma, and hue angle values. Whereas the hardness and chewiness of rehydrated DSD samples were better than HAD samples because of higher dry matter holding capacity in DSD. Apart from color retention, the DSD samples showed better rehydration capacity and a good texture upon rehydration than HAD slices.

This research study explores the addition of chromium (Cr⁶⁺) ions as a nucleating agent in the alumino-silicate-glass (ASG) system (i.e., Al₂O₃-SiO₂-MgO-B₂O₃-K₂O-F). The important feature of this study is the induction of nucleation/crystallization in the base glass matrix on addition of Cr⁶⁺ content under annealing heat treatment (600 ± 10 °C) only. The melt-quenched glass is found to be amorphous, which in the presence of Cr⁶⁺ ions became crystalline with a predominant crystalline phase, Spinel (MgCr₂O₄). Microstructural experiment revealed the development of 200–500 nm crystallite particles in Cr⁶⁺-doped glass-ceramic matrix, and such type microstructure governed the mechanical properties. The machinability of the Cr-doped glass-ceramic was thereby higher compared to base alumino-silicate glass (ASG). From the nano-indentation experiment, the Young’s modulus was estimated 25(±10) GPa for base glass and increased to 894(±21) GPa for Cr-doped glass ceramics. Similarly, the microhardness for the base glass was 0.6(±0.5) GPa (nano-indentation measurements) and 3.63(±0.18) GPa (micro-indentation measurements). And that found increased to 8.4(±2.3) (nano-indentation measurements) and 3.94(±0.20) GPa (micro-indentation measurements) for Cr-containing glass ceramic.

Two-dimensional hexagonal boron nitride nanosheets (h-BNNS) were synthesized on silver (Ag) substrates via a scalable, room-temperature atmospheric pressure plasma (APP) technique, employing borazine as a precursor. This approach overcomes the limitations of conventional chemical vapor deposition (CVD), which requires high temperatures (>800 °C) and low pressures (10⁻² Pa). The h-BNNS were characterized using FT-IR spectroscopy, confirming the presence of BN functional groups (805 cm⁻¹ and 1632 cm⁻¹), while FESEM/EDS revealed uniform nanosheet morphology with reduced particle size (80.66 nm at 20 min plasma exposure) and pore size (28.6 nm). XRD analysis demonstrated high crystallinity, with prominent h-BN (002) and h-BN (100) peaks, and Scherrer calculations indicated a crystallite size of ~15 nm. The coatings exhibited minimal disruption to UV-VIS reflectivity, maintaining Ag’s optical properties. Crucially, Vickers hardness tests showed a 39% improvement (38.3 HV vs. 27.6 HV for pristine Ag) due to plasma-induced cross-linking and interfacial adhesion. This work establishes APP as a cost-effective, eco-friendly alternative for growing h-BNNS on temperature-sensitive substrates, with applications in optical mirrors, corrosion-resistant coatings, energy devices and gas sensing.