Aiming at the current problems of poor dynamic reconstruction of UAV aerial remote sensing images and low image clarity, the dynamic reconstruction method of UAV aerial remote sensing images based on compression perception is proposed. Construct a quality reduction model for UAV aerial remote sensing images, obtain image feature information, and further noise reduction preprocessing of UAV aerial remote sensing images to better improve the resolution, spectral and multi-temporal trends of UAV aerial remote sensing images, and effectively solve the problems of resource waste such as large amount of sampled data, long sampling time and large amount of data transmission and storage. Maximize the UAV aerial remote sensing images sampling rate, reduce the complexity of dynamic reconstruction of UAV aerial remote sensing images, and effectively obtain the research requirements of high-quality image reconstruction. The experimental results show that the proposed dynamic reconstruction method of UAV aerial remote sensing images based on compressed sensing is correct and effective, which is better than the current mainstream methods.

In order to explore the influence of the ferroelectric surface on the structure and properties of semiconductor oxides, the growth of CdS nanocrystals was regulated and controlled by taking single-crystal perovskite PbTiO₃ nanosheets as the substrate through a simple hydrothermal method. Through composition design, a series of PbTiO₃-CdS nanocomposite materials with different loading concentrations were prepared, and their microstructure and photocatalytic properties were systematically analyzed. Studies show that in the prepared product, CdS nanoparticles selectively grow on the surfaces of PbTiO₃ nanosheets, and their morphology is affected by the exposed surfaces of PbTiO₃ nanosheets. There is a clear interface between the PbTiO₃ substrate and CdS nanoparticles. The concentration of the initial reactant and the time of hydrothermal reaction also significantly affect the crystal morphology of CdS. Photocatalysis studies have shown that the prepared PbTiO₃-CdS nanocomposite material has a significant degradation effect on 10 mg/L of Rhodamine B aqueous solution. The degradation efficiency rises with the increase of CdS loading concentration. When degrading 10 mg/L Rhodamine B aqueous solution, the PbTiO₃-CdS sample with a mass fraction of 3% can reach a degradation rate of 72% within 120 min.

Developing Asia’s infrastructure gap results from both inadequate public resources and a lack of effective channels to mobilize private resources toward desired outcomes. The public-private partnership (PPP) mechanism has evolved to fill the infrastructure gap. However, PPP projects are often at risk of becoming distressed, or worst, being terminated because of the long-term nature of contracts and the many different stakeholders involved. This paper applies survival-time hazard analysis to estimate how project-related, macroeconomic, and institutional factors affect the hazard rate of the projects. Empirical results show that government’s provision of guarantees, involvement of multilateral development banks, and existence of a dedicated PPP unit are important for a project’s success. Privately initiated proposals should be regulated and undergo competitive bidding to reduce the hazard rate of the project and the corresponding burden to the government. Economic growth leads to successful project outcomes. Improved legal and institutional environment can ensure PPP success.

Dust is one of the atmospheric pollutants that have adverse environmental effects and consequences. Dust fall contains particles of 100 microns or even smaller ones, which fall from the atmosphere onto the earth surface. The aim of this study is to determine the concentration of lead in dust fall samples in order to study the pollution level of this element in Zahedan, Sistan and Baluchistan Province, Iran. Therefore, sampling was carried out using 30 marble dust collectors (MDCO) for 3 months in the spring of 2015 to investigate the quantitative variation and spatial analysis of lead content in dust fall. These dust collectors were placed at 30 stations on the building roofs with a height of approximately 1.5 meters across the city. According to the results, the mean lead concentration in the spring was 90.16 mg/kg. In addition, the zoning map of lead content shows that the lowest level of lead was measured at Imam Khomeini station while the highest amount of lead appeared in Mostafa Khomeini station.

Nanotransformations of a blanket at the fair dimensional combined processing with imposing of electric field the tool in the form of untied metal granules are considered. An object of researches are the figurine details applied in aviation, the missile and space equipment and in the oil and gas industry: driving wheels and a flowing part of cases of turbo-pump units, screws, krylchatka where there are sites of variable curvature with limited access of the tool in a processing zone.It is shown that the combination in the combined process of two-component technological environments of current carrying granules and the electroconductive liquid environment given with a high speed to a processing zone allows to receive the required quality of a blanket; action of electric field from a source with the increased tension allows to create at fair dimensional processingthe required peening from blows of firm granules. It gives the chance to raise a resource and durability of responsible knots of the aerospace equipment and oil and gas equipment, to expand the field of use of the combined processing with untied granules on a detailwith the sitesnot available to processing by a profile electrode.

Application of nanoparticles have been proven to aid heat transfer in engineering systems. This work experimentally investigated the performance of a domestic refrigerator under the influence of Al₂O₃ nanoparticles dispersed in mineral oil based lubricant at different charges (40, 60 and 80 g) of LPG refrigerant. The performance of the system was then investigated using test parameters including: power consumption, evaporator air temperature (pull-down time), to attain the specified International Standard Organisation (ISO) requirement for standard evaporator air temperature with small refrigerator size. Results showed improved pull down time and steady state evaporator air temperatures for the nano-lubricant based LPG. Improvement of about 11.79% in coefficient of performance (COP) was obtained with Al₂O₃-lubricant based LPG at 40g charge on the refrigerator system, while reduction of about 2.08% and 4.41% in COP were observed at 60 and 80 g charge of LPG based on Al₂O₃-lubricant respectively. Furthermore, reduction of about 13.4% and 19.53% in the power consumption of the system were observed at 40 and 60g charges of Al₂O₃-lubricant based LPG, whereas at 80 g, an increase of about 1.28% was recorded. Using Al₂O₃-LPG nano-refrigerant in domestic refrigerators is economical  and also a better alternative to pure LPG.