Providing and using energy efficiently is hampered by concerns about the environment and the unpredictability of fossil fuel prices and quantities. To address these issues, energy planning is a crucial tool. The aim of the study was to prioritize renewable energy options for use in Mae Sariang’s microgrid using an analytical hierarchy process (AHP) to produce electricity. A prioritization exercise involved the use of questionnaire surveys to involve five expert groups with varying backgrounds in Thailand’s renewable energy sector. We looked at five primary criteria. The following four combinations were suggested: (1) Grid + Battery Energy Storage System (BESS); (2) Grid + BESS + Solar Photovoltaic (PV); (3) Grid + Diesel Generator (DG) + PV; and (4) Grid + DG + Hydro + PV. To meet demand for electricity, each option has the capacity to produce at least 6 MW of power. The findings indicated that production (24.7%) is the most significant criterion, closely followed by economics (24.2%), technology (18.5%), social and environmental (18.1%), and structure (14.5%). Option II is strongly advised in terms of economic and structural criteria, while option I has a considerable advantage in terms of production criteria and the impact on society and the environment. The preferences of options I, IV, and III were ranked, with option II being the most preferred choice out of the four.

The chemical reinforcement of sandy soils is usually carried out to improve their properties and meet specific engineering requirements. Nevertheless, conventional reinforcement agents are often expensive; the process is energy-intensive and causes serious environmental issues. Therefore, developing a cost-effective, room-temperature-based method that uses recyclable chemicals is necessary. In the current study, poly (styrene-co-methyl methacrylate) (PS-PMMA) is used as a stabilizer to reinforce sandy soil. The copolymer-reinforced sand samples were prepared using the one-step bulk polymerization method at room temperature. The mechanical strength of the copolymer-reinforced sand samples depends on the ratio of the PS-PMMA copolymer to the sand. The higher the copolymer-to-sand ratio, the higher the sample’s compressive strength. The sand (70 wt.%)-PS-PMMA (30 wt.%) sample exhibited the highest compressive strength of 1900 psi. The copolymer matrix enwraps the sand particles to form a stable structure with high compressive strengths.

This research paper explores the influence of first-order chemical reactions on the sustainable properties of electrically conducting magnetohydrodynamic (MHD) fluids in a vertical channel with the unique characteristics of Jeffrey fluid flow. The mathematical model of MHD flow with Jeffrey fluid and chemical reaction incorporates the impacts of viscous dissipation, Joule heating, and a non-Newtonian fluid model with viscoelastic properties in the flow regions. The governing equations of the flow field were solved using the finite difference method, and the impacts of flow parameters on the flow characteristics were discussed numerically using a graphical representation. It’s revealed that increasing the Jeffrey parameter results in a decline in the velocity field profiles. Also, species concentration field profiles decline with higher values of the destruction chemical reaction parameter. The findings of this study have significant implications for various engineering applications, including energy generation, aerospace engineering, and material processing. Additionally, the inclusion of Jeffrey’s fluid flow introduces a viscoelastic component, enhancing the complexity of the fluid dynamics.

Publications overestimating the medical and ecological sequels of a slight anthropogenic increase in the radiation background have been reviewed recently with examples of different organs and pathological conditions. The overestimation contributed to the strangulation of atomic energy. The use of nuclear energy for electricity production is on the agenda today due to the increasing energy needs of humankind. Apparently, certain scientific writers acted in the interests of fossil fuel producers. Health risks and environmental damage are maximal for coal and oil, lower for natural gas, and much lower for atomic energy. This letter is an addition to previously published materials, this time focused on studies of cataracts in radiation-exposed populations in Russia. Selection and self-selection bias are of particular significance. Apparently, the self-reporting rate correlates with dose estimates and/or with professional awareness about radiation-related risks among nuclear workers or radiologic technologists, the latter being associated with their work experience/duration and hence with the accumulated dose. Individuals informed of their higher doses would more often seek medical advice and receive more attention from medics. As a result, lens opacities are diagnosed in exposed people earlier than in the general population. This explains dose-effect correlations proven for the incidence of cataracts but not for the frequency of cataract surgeries. Along the same lines, various pathological conditions are more often detected in exposed people. Ideological bias and the trimming of statistics have not been unusual in the Russian medical sciences. It is known that ionizing radiation causes cataracts; however, threshold levels associated with risks are understudied. In particular, thresholds for chronic and fractionated exposures are uncertain and may be underestimated.

The aim of the present study was to determine the effects of single and mixed infections of nematode (Meloidogyne javanica), fungus (Fusarium oxysporum) and bacterium (Xanthomonas axonopodis) on nodulation and pathological parameters of Bambara groundnut (Vigna subterrenea (L.) Verdc.) in field condition. Nematode infested field was used while other pathogens were obtained from diseased plants. The Randomized Complete Block Design (RCBD) was adopted in a 5 × 9 × 5 factorial design (5 blocks, 9 treatments and 5 replicates per treatments) resulting in 225 experimental units. In each experimental unit, three seeds were sown to a depth of 5cm and thinned to one plant per planting hole after germination at day 7. Treatments were inoculated into test plant following standard methods. As a result, the control treatment recorded the highest number of nodules (64.0 ± 6.91), followed by bacterium (45.2 ± 5.11) while N + F + B had the lowest number of root nodules (23.4 ± 2.42). Simultaneous treatment (N + F + B) gave the highest percentage reduction in nodulation (63.44%), followed by treatment N + F7 (56.25%). Fungus treatment recorded the highest mean wilted plants (3.8 + 0.20) followed by N + F7 treatment (3.40 + 0.40). Gall formation in the nematode treatment increased proportionately by 56.33% as the highest recorded, followed by treatment N + F7 with 50.0%. Treatment N + F7 had the highest reproduction factor (Rf) value of 9.30 followed by nematode (8.30), N + B7 (7.40), N + F + B (6.80) and N + F14 (6.50). Zero (0) Rf value was recorded in fungus, bacterium and control treatments. The observed differences in nodulation and pathological parameters among the treatments are significant (P < 0.05). The data provided in this work is important in the control of the three pathogens affecting the productivity of Bambara nut. Formulation of a single protectant should be designed to have potent effects on the three pathogens to achieve effective protection and good production of Bambara nut.