The structure and diversity of tree species in a temperate forest in northwestern Mexico was characterized. Nine sampling sites of 50 × 50 m (2,500 m²) were established, and a census of all tree species was carried out. Each individual was measured for total height and diameter at breast height. The importance value index (IVI) was obtained, calculated from the variable abundance, dominance and frequency. The diversity and richness indices were also calculated. A total of 12 species, four genera and four families were recorded. The forest has a density of 575.11 individuals and a basal area of 23.54/m². The species of Pinus cooperi had the highest IVI (79.05%), and the Shannon index of 1.74.

Magnetic graphene oxide nanocomposites (M-GO) were successfully synthesized by partial reduction co-precipitation method and used for removal of Sr(II) and Cs(I) ions from aqueous solutions. The structures and properties of the M-GO was investigated by X-ray diffraction, Fourier transformed infrared spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy, scanning electron microscopy, vibrating sample magnetometer (VSM) and N₂-BET measurements. It is found that M-GO has 2.103 mg/g and 142.070 mg/g adsorption capacities for Sr(II) and Cs(I) ions, respectively. The adsorption isotherm matches well with the Freundlich for Sr(II) and Dubinin–Radushkevich model for Cs(I) and kinetic analysis suggests that the adsorption process is pseudo-second-ordered.

This work investigates epoxy composites reinforced by randomly oriented, short glass fibres and silica microparticles. A full-factorial experiment evaluates the effects of glass fibre mass fraction (15 wt% and 20 wt%) and length (5 mm and 10 mm), and the mass fraction of silica microparticles (5 wt% and 10 wt%) on the apparent density and porosity, as well as the compressive and tensile strength and modulus of the hybrid composites. Hybrid epoxy composites present significantly higher tensile strength (9%) and modulus (57%), as well as compressive strength (up to 15%) relative to pure epoxy.

Distributed biomass energy technology has strong adaptability to the types of raw materials, flexible project scale, can meet the needs of special users, better economy in small scale, easier commercial development, in line with the characteristics of biomass resources and China’s national conditions. The distributed utilization of biomass energy mainly includes biomass briquette fuel and biogas. The key technologies include biomass briquette fuel processing and combustion, large and medium-sized biogas engineering technology, biomass gasification pyrolysis and gas utilization. At present, China’s distributed biomass energy technology is mainly in the stage of technological improvement and application demonstration. It is expected that by 2030, most of the key technologies will be basically mature and have the conditions for industrialization. The main development direction of China’s distributed biomass energy industry is the replacement of traditional coal-fired gas, urban/rural clean living energy supply, and rural ecological environmental protection. The pollution caused by burning coal/fuel oil, and at the same time centering on the national new urbanization strategy, provide sustainable clean energy for the construction of new rural areas, and improve the level of rural ecological and environmental protection. At present, the main bottleneck restricting the development of distributed biomass energy industry is economy and reliability. The state should increase investment in technological innovation and policy support, convert the environmental and social benefits of biomass energy into cost benefits, and promote biomass energy. The development of the industry can be distributed and utilized.

Plasma thermal gasification can be one of the most relevant and environmentally friendly technologies for waste treatment and has gained interest for its use in thethermos-conversion of biomass. In this perspective, the objective of this study is to evaluate the gasification of sugarcane bagasse by studying the effective areas of operation of this process and to establish a comparison with conventional autothermal gasification. A thermochemical equilibrium model was used to calculate the indicators that characterize the performance of the process on its own and integrated with a combined cycle. As a result, it was obtained that plasma and gasification of bagasse is technically feasible for the specific net electrical production of 4 MJ with 30 % electrical efficiency, producing a gas with higher calorific value than autothermal gasification. The operating points where the electrical energy production and the cold gas efficiency reach their highest values were determined; then the effects of the operational parameters on these performance indicators were analyzed.

Adsorption is a widely used method for the treatment of dissolved contaminants. Various agro-industrial wastes have been explored as potential adsorbents, showing high efficiency in dye removal. Each adsorbate-adsorbent pair needs kinetic, and equilibrium models to scale up this process. In this work, the equilibrium, kinetics and thermodynamics of the corn Tuza-Red 40 system were evaluated under batch system at ph = 2.0 at temperatures of 25, 40, and 55 °C. The Langmuir, Freundlich and Temkin models were selected for the isotherm representation, while the Lagergren, Ho, and Elovich equations for the kinetics of the process. The Freundlich model presented the best fit to the isotherms, the adsorption kinetics was best described by the Ho equation, and the values for Gibbs free energy and entropy indicated the spontaneity and feasibility of the process.