Humic substances are used in agriculture as promoters of plant growth, especially of the root system. The objective of the work was to evaluate the effect of the application of different doses of fulvic acid on the growth and productivity of American lettuce, Raider Plus cultivar. The experimental design used was entirely randomized, with five treatments of fulvic acid 0, 1, 2, 4, 8 mL·L^-1 and four repetitions, applied at the time of transplanting. Two experiments were conducted simultaneously: one in the greenhouse, where fresh and dry mass of the aboveground and root parts, length and volume of the roots were evaluated; and the other in the field, where, at the end of the cycle, fresh and dry mass of the aboveground parts, number of leaves, stem length and average head circumference were evaluated. The application of different doses of fulvic acid promoted the growth of lettuce plants, especially the root system. The emission of roots, with predominance, of those of smaller diameter, was found in the higher concentrations of fulvic acid. The number of leaves and the average circumference of the head expressed responses in the concentrations of fulvic acid.

In this paper, an improved mathematical model for flashover behavior of polluted insulators is proposed based on experimental tests. In order to determine the flashover model of polluted insulators, the relationship between conductivity and salinity of solution pollution layer of the insulator is measured. Then, the leakage of current amplitude of four common insulators versus axial, thermal conductivity and arc constants temperature was determined. The experimental tests show that top leakage distance (TLd) to bottom leakage distance (BLd) ratio of insulators has a significant effect on critical voltage and current. Therefore, critical voltage and current were modeled by TLd to BLd ratio Index (M). Also, salinity of solution pollution layer of the insulators has been applied to this model by resistance pollution parameter. On the other hand, arc constants of each insulator in new model have been identified based on experimental results. Finally, a mathematical model is intended for critical voltage against salinity of solution pollution layer of different insulators. This model depends on insulator profile. There is a good agreement between the experimental tests of pollution insulators obtained in the laboratory and values calculated from the mathematical models developed in the present study.

Considering the need to adopt more sustainable agricultural systems, it is important that sweet potato breeding programs seek to increase not only root productivity, but also the productivity and quality of branches for silage production. The objective was to evaluate the genetic divergence and the importance of traits associated with the production and quality of branch silage in sweet potato genotypes. The experiment was conducted on the JK Campus of the Federal University of Vales do Jequitinhonha and Mucuri Valleys in a randomized block design with 12 treatments and four repetitions. Twelve characteristics of branches and silage were evaluated. There was genetic variability between the genotypes, making it possible to select parents divergent for future breeding programs for silage production. The genotypes BD-54 and BD-31TO were the most divergent in relation to the others, being indicated its use in crossbreeding aiming the improvement of the culture for silage, once the high performance per se of all genotypes evaluated has already been verified in previous works. The characteristics Na, TDN and NDF were those that most contributed to the divergence.

Afforestation is a main tool for preventing desertification and soil erosion in arid and semiarid regions of Iran. Large-scale afforestation, however, has poorly understood consequences for the future ecosystems in the term of ecosystems protection. The objective of the present study is to identify changes in soil properties following different intervals of planting of Ailanthus altissima (tree of heaven) in semiarid afforestation of Iran (Chitgar Forest Park, Tehran). For this purpose, sand, silt and clay ratios, bulk density, soil moisture, pH, electrical conductivity, phosphorus, potassium, magnesium, calcium, sodium, total soil N, and total carbon was measured. Our study highlighted the potential of the invasive trees by A. altissima, to alter soil properties along chronosequence. Almost all soil quality attributes showed a declining trend with stand age. A continuous decline in soil quality indicated that the present land management may not be sustainable. Therefore, an improved management practice is imperative to sustain soil quality and maintain long-term productivity of plantation forests. Thinning activity will be required to reduce the number of trees competing for the same nutrients especially in a older stand to protect forest soils.

This study examines conditions that impact PPP delivery success or failure in the roadways sector in India using Qualitative Comparative Analysis. QCA is well-suited for problems where multiple factors combine to create pathways leading to an outcome. Past investigations have compared PPP and non-PPP project delivery performance, but this study examines performance within PPPs by uncovering a set of conditions that combine to influence the success or failure road PPP project delivery in India. Based on data from 21 cases, pathways explaining project delivery success or failure were identified. Specifically, PPPs with high concessionaire equity investment and low regional industrial activity led to project delivery success. Projects with lower concessionaire equity investment and low reliance on toll revenue and with either: (a) high project technical complexity or (b) high regional industrial activity, led to project delivery failure. The pathways identified did not have coverage values that they were extremely strong. Coverage strength was hindered by lack of access to information on additional conditions that could be configurationally important. Further, certain characteristics of the Indian market limit generalization. Identification of combinations of conditions leading to PPP project delivery success or failure improves knowledge of the impacts of structure and characteristics of these complex arrangements. This study is one of the first to use fuzzy QCA to understand project delivery success/failure in road PPP projects. Moreover, this study takes into account factors specific to a sector and delivery mode to explain project delivery performance.

Helical deep hole drilling is a process frequently used in industrial applications to produce bores with a large length to diameter ratio. For better cooling and lubrication, the deep drilling oil is fed directly into the bore hole via two internal cooling channels. Due to the inaccessibility of the cutting area, experimental investigations that provide information on the actual machining and cooling behavior are difficult to carry out. In this paper, the distribution of the deep drilling oil is investigated both experimentally and simulatively and the results are evaluated. For the Computational Fluid Dynamics (CFD) simulation, two different turbulence models, i.e. the RANS k-ω-SST and hybrid SAS-SST model, are used and compared. Thereby, the actual used deep drilling oil is modelled instead of using fluid dynamic parameters of water, as is often the case. With the hybrid SAS-SST model, the flow could be analyzed much better than with the RANS k-ω-SST model and thus the processes that take place during helical deep drilling could be  simulated with realistic details. Both the experimental and the simulative results show that the deep drilling oil movement is almost exclusively generated by the tool rotation. At the tool’s cutting edges and in the flute, the flow velocity drops to zero for the most part, so that no efficient cooling and lubrication could take place there. In addition, cavitation bubbles form and implode, concluding in the assumption that the process heat is not adequately dissipated and the removal of chips is adversely affected, which in turn can affect the service life of the tool and the bore quality. The carried out investigations show that the application of CFD simulation is an important research instrument in machining technology and that there is still great potential in the area of tool and process optimization.