Nowadays, copper and zinc nanoparticles are widely employed in a variety of applications. With nanoscale particle sizes, copper oxide/zinc oxide composite is easily synthesized using a variety of techniques, including hydrothermal, microwave, precipitation, etc. In the current work, chemical precipitation is used to create a copper oxide/zinc oxide nanocomposite. XRD analysis was used to determine the nanocomposite’s structural characteristics. Through SEM analysis, the surface morphological properties are investigated. EDAX is used to study the chemical composition of produced materials, while UV/Visible spectroscopy is used to determine their optical properties. The assessment of the copper oxide/zinc oxide nanocomposite’s degrading property on dyes like methyl red and methyl orange under UV and visible light are the main objectives of the current work.

The electrospinning precursor solution was prepared by dissolving polyvinyl pyrrolidone as template, tetrabutyl titanate as titanium source, and acetic acid as inhibitor. The TiO₂ nanofilms were prepared by precursor solution electrospinning and subsequent calcination. Thermal gravimetric analysis (TG), scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and transmission electron microscopy (TEM) were used to characterize and analyze the samples. The influence of technological parameters on spinning fiber morphology was also studied. The results indicate that the TiO₂ nanofibers morphology is good when the parameters are as follows: voltage 1.4×10⁴ V，spinning distance 0.2 m，translational velocity 2.5×10^-3 m·s^-1, flow rate 3×10^-4 m·s^-1, and needle diameter 3×10^-4 m. The diameter of the fibers is about 150 nm. With the 1×10^-4 mol·L^-1 methylene blue solution used as simulated degradation target, the degradation rate is 95.8% after 180 minutes.

Ce⁴⁺-doped nanometer ZnO powder was synthesized by so-l gel method. The microstructures and properties of the samples were characterized through XRD, UV-Vis and FTIR. The results indicated that the Ce⁴⁺ was successfully incorporated into ZnO, and the diameter of the nanometer was about 10.7nm. It induced the redshifting in the UV-Vis spectra. The photocatalytic activity of the samples was investigated using methylene blue (MB) as the model reaction under irradiation with ultraviolet light. The results showed that the doping of Ce⁴⁺ could increase the photocatalytic activities of ZnO nanopowders and that the best molar ratio of Ce⁴⁺ was n(Ce)/n(Zn) = 0.05, that the surfactant was sodium dodecyl sulfate, and that the nanometer ZnO was calcinated at 550 ℃ for 3 hours. Meanwhile, it inspected the effect of photocatalytic efficiency through the pH of MB, the amount of catalyst, and illumination time. The experimental results revealed that the initial mass concentration of MB was 10 mg/L, that the pH value was 7-8, that the dosage of Ce⁴⁺/ZnO photo-catalyst was 5 g/L, that the UV-irradiation time was 2 h, and that the removal rate of MB reached above 85%. Under the optimized conditions, the degradation rate of real dye wastewater was up to 87.67% and the removal efficiency of COD was 63.5%.

Synthesis of macro-mesoporous Titania (Titanium dioxide-TiO₂) nanospheres was successfully achieved using a modified template-free methodology to incorporate macroporous channels into a mesoporous TiO₂ framework to form mixed macro-mesoporous TiO₂ spheres (MMPT), which were doped with carbon dots (C-dots) to form improved nanocomposites (C-dots@MMPT). Elemental composition, surface bonding and optical properties of these nanocomposites were characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR) and ultraviolet-visible absorption spectroscopy (UV-VIS). Evaluation of photocatalytic activity for each (C-Dots@MMPT) sample was performed via degrading the Methylene Blue (MB) dye compared with bare samples (MMPT) under visible light irradiation using 300 Watt halogen lamp.