Public-Private Partnerships (PPPs) are mostly presented as a means to introduce efficient procurement methods and better value for money to taxpayers. However, the complexity of the PPP mechanism, their lack of transparency, accounting rules and implicit liabilities make it often impossible to perceive the amount of public expenditure involved and the long-run impact on taxpayers, providing room for fiscal illusion, i.e., the illusion that PPPs are much less expensive than traditional public investments. This psaper, thanks to a systematic review of the literature on the EU countries experience, tries to unveil the sources of this illusion by looking at the reasons behind the PPPs’ choice, their real costs, and the sources of fiscal risks. The literature suggests that PPPs are more costly than public funding, especially when contingent liabilities are not taken into account, and are employed as mechanisms to circumvent budgetary restrictions and to spend off-balance. The paper concludes that the public sector should share more risks with private sectors by reducing the amount of guarantees, and should prevent governments from operating through a sleight of hand that deflects attention away from off-balance financing, by applying a neutral fiscal recording system.

The cross wire projection welding of wires (Al 5182, = 4 mm) performed using the conventional (i.e. pneumatic) electrode force system was subjected to thorough numerical analysis. Calculations were performed until one of adopted boundary conditions, i.e., maximum welding time, maximum penetration of wires, the occurrence of expulsion or the exceeding of the temperature limit in the contact between the electrode and the welded material was obtained. It was observed that the ring weld was formed within the entire range of welding parameters. The process of welding was subjected to optimisation through the application of a new electromechanical electrode force system and the use of a special hybrid algorithm of electrode force and/or displacement control. Comparative numerical calculations were performed (using SORPAS software) for both electrode force systems. Technological welding tests were performed using inverter welding machines (1 kHz) provided with various electrode force systems. The research also involved the performance of metallographic and strength (peeling) tests as well as measurements of welding process characteristic parameters (welding current and voltage).
The welding process optimisation involving the use of the electromechanical force system and the application of the hybrid algorithm of force control resulted in i) more favourable space distribution of welding power, ii) energy concentration in the central zone of the weld, iii) favourable (desired) melting of the material within the entire weld transcrystallisation zone and iv) obtainment of a full weld nugget.

Nothofagus pumilio forests constitute the most economically important forest stand in southern Argentina and Chile. Total volume stocking and volumetric yield vary according to site quality, degree of occupation, growth stage and forest history of the stand. The objective of this work was to evaluate the stocking and the productive potential in quantity and quality of products for the sawmilling industry, using three harvesting systems (short logs, long logs and complete shafts) in the protection cut of a N. pumilio forest of site quality III in Tierra del Fuego (Argentina). The trials were conducted in an irregular mature forest with two strata and abundant regeneration (3.0 ha; RDI 93.8–113.4%). Total volumes varied between 726.5 and 850.3 m³∙ha^-1, with a volume/basal area ratio of 11.8 to 12.1 m³∙m^-2. The harvesting rates obtained were: 45.5% for complete logs, 21.3% for long logs and 22.4% for short logs. A model was used to estimate the timber volume for each system, where full shafts resulted in a significant increase in timber volume. Considering new alternatives in the planning of harvesting in forest management for N. pumilio forests, such as the system of complete shafts, allows obtaining higher harvesting rates, increasing the benefits for the forestry company and minimizing the damage to the forest, due to the shorter distance of the machinery in the forest harvesting.

Application of nanoparticles have been proven to aid heat transfer in engineering systems. This work experimentally investigated the performance of a domestic refrigerator under the influence of Al₂O₃ nanoparticles dispersed in mineral oil based lubricant at different charges (40, 60 and 80 g) of LPG refrigerant. The performance of the system was then investigated using test parameters including: power consumption, evaporator air temperature (pull-down time), to attain the specified International Standard Organisation (ISO) requirement for standard evaporator air temperature with small refrigerator size. Results showed improved pull down time and steady state evaporator air temperatures for the nano-lubricant based LPG. Improvement of about 11.79% in coefficient of performance (COP) was obtained with Al₂O₃-lubricant based LPG at 40g charge on the refrigerator system, while reduction of about 2.08% and 4.41% in COP were observed at 60 and 80 g charge of LPG based on Al₂O₃-lubricant respectively. Furthermore, reduction of about 13.4% and 19.53% in the power consumption of the system were observed at 40 and 60g charges of Al₂O₃-lubricant based LPG, whereas at 80 g, an increase of about 1.28% was recorded. Using Al₂O₃-LPG nano-refrigerant in domestic refrigerators is economical  and also a better alternative to pure LPG.

As an important ecosystem type in the coastal zone, mangroves have important ecological functions, such as maintaining coastal biodiversity, preventing wind and consolidating the coast, promoting silt and building land. It is of great significance to understand the protected status of mangroves in the context of climate change and rapid urbanization. Based on the mangrove classification data from remote sensing interpretation, through vacancy analysis, the in-situ protection status of mangroves in China is analyzed. The results show that the total area of mangroves distributed in China is 264 km² (excluding the statistical data of Hong Kong, Macao and Taiwan), of which 61.4% are protected in natural reserves. In terms of the main provinces where mangroves are distributed, the mangrove area distributed in Hainan Province is small but the protection proportion is high, while the mangrove area distributed in Guangxi and Guangdong Province is large but the proportion of protected areas is relatively low. Among the three mangrove types, Rhizophora apiculate-Xylocarpus granatum and Rhizophora stylosa-Bruguiera gymnorrhiza had high proportions (>90%) covered by reserves, but relatively small areas. In contrast, Kandelia candel-Aegiceras corniculatum-Avicennia marina had relatively low reserve coverage (52.6%), but a large area. The study puts forward the key areas of mangrove distribution outside the nature reserve, and suggests that they should be protected by delimiting ecological protection red lines.

Using the rank scale rule, taking 47 major port cities in China from 2001 to 2015 as research samples, this paper discusses the rank scale characteristics and hierarchical structure of coastal port city system from a multi-functional perspective, and divides the coupling type of multi-functional development based on shipping logistics. The research shows that: 1) from 2001 to 2015, the scale-free area of manufacturing function order scale distribution in the coastal port city system appeared bifractal structure, the hierarchical segmentation characteristics appeared, and the other functions were single fractal; From the perspective of long-term evolution, only the order and scale distribution of shipping logistics function has developed from centralization to equilibrium, while the business function, manufacturing function (scale-free region I), modern service function and population distribution function are in a centralized situation. 2) The hierarchical structure of coastal port city system has gradually changed from pyramid structure to spindle structure, and generally formed five levels: national hub, regional hub, regional sub center, regional node and local node. 3) From the perspective of multi-functional coupling types, the traditional functions of port cities are generally ahead, while the high-end service functions lag behind, and the improvement speed of urban functions is slow and tends to be flat, indicating that the multi-functional development of China’s coastal port cities is still at a low level, and the industrial system structure needs to be further optimized. 4) From the perspective of port cities at different levels, the functions of regional hub cities and regional sub central cities are in the stage of rapid growth; regional and local node cities are still in the growth stage of traditional functions such as industry and commerce.