No less than 60% of timber production in Peru’s natural forests is the result of informal or illegal extractive activities that, by definition, are not sustainable. This article aims to demonstrate that even legitimate timber, such as timber harvested in more than 6 million hectares of forest concessions, does not meet the basic requirements of sustainable forest management. Forestry legislation itself, which does not emphasize forest management, institutional weaknesses and the socioeconomic environment are the main causes. In addition, the cutting cycles and the authorized minimum diameters, among other practices, do not allow the renewal of the resource and increase its degradation.

While there has been much discussion about the large infrastructure needs in Asia and the Pacific, less attention has been paid to public expenditure efficiency in infrastructure services delivery. New constructions are not the only solution, especially when governments have limited capital to invest. Globally, new infrastructure projects face delays and cost overruns, leading to an inefficient use of public resources. The root causes include the lack of transparency in project selection, the lack of project preparation, the silo approach by public entities in assessing feasibility studies, and the lack of public sector capacity to fully develop a bankable pipeline of projects. To tackle these issues, governments need a smarter investment approach and to do so, enhancing public service efficiency is very crucial. The paper suggests a “whole life cycle” (WLC) approach as the main strategic solution for the discussed issues and challenges. We expand the definition of WLC to include the entire life cycle of the infrastructure asset from need identification to its disposal. The stages comprise planning, preparation, procurement, design, construction, operation and maintenance, and disposal. This is because we believe any efficient or inefficient decision throughout such a wide life cycle influences the quality of public services. Hence, in this holistic approach, infrastructure life cycle consists of four phases: planning, preparation, procurement, and implementation. Governments could enhance public efficiency and thus improve access to finance throughout the WLC by several solutions. These are (i) preparing infrastructure master plan and pipelines and long-term budgeting during the planning phase; (ii) establishing framework and guidelines and improving governance during preparation phase; (iii) promoting standardization, transparency, open government, and contractual consistency during the procurement phase; and finally (iv) continued role of government and total asset management during the implementation phase. In addition to these phase-specific means, key WLC solutions include proper use of technology, capacity building, and private participation in general and public-private partnership (PPP) in particular.

BiVO₄ was hydrothermally synthesized under different preparing conditions and characterized by XRD, SEM, Raman spectrum and BET specific surface area. The influence of different pH value and annealing temperature and hydrothermal time on the morphologies and structures of the BiVO₄ samples was investigated systematically. It can be found that annealing would eliminate the effects caused by the pH of precursor, heating temperature and heating time, but preparing conditions still influenced the size and specific surface area of samples. Furthermore, the photocatalytic activities of the fabricated BiVO₄ were also evaluated by the degradation of methyl blue in aqueous solution under UV and visible light irradiation.

The wealth of nations depends on the quality of their infrastructure. Often, however, infrastructure suffers from ineffective investments and poor maintenance. Proposed solutions, such as New Public Management or Public-Private Partnerships (PPPs) tend to develop into Politicians-Private Partnerships as politicians collude with private firms to exploit present and future tax-payers. Therefore, it is necessary to give citizens better control over collective decision making. While there is a significant economic literature on empowering citizens via decentralization and direct democratic institutions, the role of electoral rules has thus far been rather neglected. An interesting case in point is Switzerland, which is well known for its high-quality infrastructure, extensive decentralization, and direct democracy. However, this paper argues that there is an additional and previously neglected institution that moves Swiss politicians away from client politics towards better serving public interest: Switzerland’s unique electoral institutions which effectively combine proportional elections with multi-seat majority elections. We explain how these institutions work, how they enhance the relationships between citizens and public and private entities, and we argue that they could be implemented in other countries.

Helical deep hole drilling is a process frequently used in industrial applications to produce bores with a large length to diameter ratio. For better cooling and lubrication, the deep drilling oil is fed directly into the bore hole via two internal cooling channels. Due to the inaccessibility of the cutting area, experimental investigations that provide information on the actual machining and cooling behavior are difficult to carry out. In this paper, the distribution of the deep drilling oil is investigated both experimentally and simulatively and the results are evaluated. For the Computational Fluid Dynamics (CFD) simulation, two different turbulence models, i.e. the RANS k-ω-SST and hybrid SAS-SST model, are used and compared. Thereby, the actual used deep drilling oil is modelled instead of using fluid dynamic parameters of water, as is often the case. With the hybrid SAS-SST model, the flow could be analyzed much better than with the RANS k-ω-SST model and thus the processes that take place during helical deep drilling could be  simulated with realistic details. Both the experimental and the simulative results show that the deep drilling oil movement is almost exclusively generated by the tool rotation. At the tool’s cutting edges and in the flute, the flow velocity drops to zero for the most part, so that no efficient cooling and lubrication could take place there. In addition, cavitation bubbles form and implode, concluding in the assumption that the process heat is not adequately dissipated and the removal of chips is adversely affected, which in turn can affect the service life of the tool and the bore quality. The carried out investigations show that the application of CFD simulation is an important research instrument in machining technology and that there is still great potential in the area of tool and process optimization.