New hybrid magnetic materials based on HDPE filled with Со and Ni nanoparticles have been prepared via the metal vapor synthesis. Properties of the metal-polymer composites have been elucidated as a function of MVS parameters and metal nature. The Faraday method has been applied to characterize the magnetic properties of the systems. The microstructure of the samples has been studied with a number of X-ray and synchrotron techniques, including XRD, EXAFS and SAXS. Core-level and valence band spectra were measured by XPS. The peak at binding energy of 282.8 eV characteristic of C-Ni bond was recorded in the C 1s spectrum. It was shown that properties of nanocomposite materials with similar compositions are determined both by the synthesis conditions and post-synthesis factors.

Nanotransformations of a blanket at the fair dimensional combined processing with imposing of electric field the tool in the form of untied metal granules are considered. An object of researches are the figurine details applied in aviation, the missile and space equipment and in the oil and gas industry: driving wheels and a flowing part of cases of turbo-pump units, screws, krylchatka where there are sites of variable curvature with limited access of the tool in a processing zone.It is shown that the combination in the combined process of two-component technological environments of current carrying granules and the electroconductive liquid environment given with a high speed to a processing zone allows to receive the required quality of a blanket; action of electric field from a source with the increased tension allows to create at fair dimensional processingthe required peening from blows of firm granules. It gives the chance to raise a resource and durability of responsible knots of the aerospace equipment and oil and gas equipment, to expand the field of use of the combined processing with untied granules on a detailwith the sitesnot available to processing by a profile electrode.

Application of nanoparticles have been proven to aid heat transfer in engineering systems. This work experimentally investigated the performance of a domestic refrigerator under the influence of Al₂O₃ nanoparticles dispersed in mineral oil based lubricant at different charges (40, 60 and 80 g) of LPG refrigerant. The performance of the system was then investigated using test parameters including: power consumption, evaporator air temperature (pull-down time), to attain the specified International Standard Organisation (ISO) requirement for standard evaporator air temperature with small refrigerator size. Results showed improved pull down time and steady state evaporator air temperatures for the nano-lubricant based LPG. Improvement of about 11.79% in coefficient of performance (COP) was obtained with Al₂O₃-lubricant based LPG at 40g charge on the refrigerator system, while reduction of about 2.08% and 4.41% in COP were observed at 60 and 80 g charge of LPG based on Al₂O₃-lubricant respectively. Furthermore, reduction of about 13.4% and 19.53% in the power consumption of the system were observed at 40 and 60g charges of Al₂O₃-lubricant based LPG, whereas at 80 g, an increase of about 1.28% was recorded. Using Al₂O₃-LPG nano-refrigerant in domestic refrigerators is economical  and also a better alternative to pure LPG.

In this study, the effect of roasting and boiling on the yield and oxidative stability of soya bean oil was investigated. The oil was soxhlet extracted and the oxidative stability was determined by the free fatty acid value, acid value and peroxide value. The results showed that the oil yield, free fatty acid value, acid value and peroxide value were significantly affected by roasting, boiling, and the thermal treatment time. The percentage oil yield in the control oil sample was 18.51%, which increased to 20.24% and 20.73% after boiling and roasting respectively, at 40mins. The corresponding free fatty acid and the peroxide value of the control oil sample were 0.14% and 2.04 meqO₂/kg, which increased to 0.82% and 6.60 meqO₂/kg by roasting, and 0.47% and 5.62 meqO₂/kg by boiling respectively. Thus the oil yield, free fatty acid value, peroxide value, and acid value increased with increasing roasting and boiling time.
The results indicate that roasting provides a higher oil yield than boiling, but boiled oil has higher oxidative stability than roasted oil.

Potassium dihydrogen phosphate, KH2PO4 (KDP) crystal is an excellent electro-optical nonlinear optical crystal with large electro-optical nonlinear coefficient, high laser damage threshold, and laser frequency doubling effect, electro-optical effect , Piezoelectric effects and other special features, widely used in inertial confinement fusion engineering (ICF) and electro-optical switching devices. Therefore, its growth mechanism, growth process and performance have been systematically studied. In the process of KDP crystal growth, it is found that the stability of the growth solution is an important factor affecting the quality of crystal growth. Therefore, in recent years, more and more research on the stability of the solution, such as the study of ph, doping, supersaturation, overheating time on the stability of the solution. Among them, the research on the doping is mostly reported, and the research on this aspect is mainly focused on two aspects. On the one hand, it is the study of the stability of the solution under doping, and the other is the effect of doping on the optical quality of the crystal. In fact, the stability of the growth solution and the quality of crystal growth is directly related to the quality, but the existing research to isolate the two researches. Therefore, the experiment will be carried out in the case of double-doped KDP solution stability, KDP crystal growth and crystal optical quality and other experiments, and in-depth analysis of the impact of solution stability and crystal optical quality of the reasons, while the solution stability and The relationship between the optical quality of the crystal is briefly analyzed.