To address the problem that the imaging inversion method based on a single model in integrated aperture imaging is difficult to effectively correct model errors and perform accurate image reconstruction, a dual-model (DM)-based integrated aperture imaging inversion method is proposed for correcting the parametric errors of the inversion model and performing highly accurate millimeter-wave image reconstruction of the target scene. In view of the different parameter sensitivities of the Fourier transform (MFFT) model and the G-matrix (GM) model, the proposed DM method first corrects the imaging parameters with errors accurately by comparing the reconstruction errors of the two models; then recon-structs a high-precision target image based on the accurate GM model with the help of an improved regularization method. It is proved by simulation experiments that the proposed DM method can effectively correct the parameter errors of the imaging model and reconstruct the target scene with high accuracy in millimeter wave images compared with the traditional single-model imaging method.

Regarding to the influence of chloride and fluoride ions on the corrosion resistance, the electrochemical behavior of Ti alloys has been deeply studied. In this work, the main goal was to investigate the electrochemical behavior of cp-Ti and Ti-Mo alloys containing 6, 10 and 15 wt% of Mo concentrations. All the samples were immersed in different solutions, such as 0.15 mol L^-1 Na₂SO₄, 0.15 mol L^-1 Ringer, 0.15 mol L^-1 Ringer plus 0.036 mol L^-1 NaF and 0.036 mol L^-1 NaF. Simulating the commercial fluorinated gels, the NaF solutions naturally-aerated were prepared with 1450 ppm of fluoride ions. The electrochemical techniques applied in this work were the open-circuit potential, cyclic voltammetry, besides the technique for chemical identification, which was X-ray photoelectron spectroscopy. The formation and growth of TiO₂ and MoO₂ were identified, without pitting corrosion. The electrochemical stability and the corrosion resistance of the Ti-Mo alloys decreased in the solutions containing chloride and fluoride ions, with an appreciative decrease especially in the fluorinated medium. The Ti-Mo alloy with higher Mo content concentration was the material with higher corrosion resistance. Therefore, it is a promising candidate as a biomaterial, once the osseointegration needs a satisfactory corrosion resistance for being achieved.

Control of key technological and benchmark flows of polymer fluids poses a number of challenges. Some of them are nowadays under active investigation and rather far from complete under­stan­ding. This review considers such phenomena as both practically important and governed by funda­mental laws of rheology and non-linear fluid mechanics. We observe, shear bands in polymeric and other complex structured fluids (like wormlike micellar solutions or soft glassy materials), birefrigerent strands, peculiarities of stress and pressure losses in fluids moving through com­plex shape domains. These and other processes involve in­ho­mo­geneity, in­stabilities and tran­sient modes creeping in flow fields. In practical aspect this is of interest in such industrial process as polymer flooding for Enhanced Oil Recovery (EOR), where a flow inhomogeneity affects a poly­mer solution injectivity and residual oil saturation. The value of viscoelasticity in the polymer flooding is estimated. The obser­va­tion is con­clu­ded by some new results on relation between polymer concentration in solutions and viscoelastic traits of benchmark flows.

Europium (Eu) doped Calcium borophosphate (CBP) phosphors were synthesized via the solid-state diffusion method. The prepared Europium (Eu) doped Calcium borophosphate (CBP) powder was heated up to 600 ℃ for 6 h for a complete diffusion of ions in the powder system. XRD results showed that the prepared phosphors exhibit a well-crystallized hexagonal phase. The complete diffusion inside the CBP/Eu powder system has been confirmed by the presence of elements such as P, O, Bi, Ca, C, Eu, and B. Apart from that, the synthesized powder system has shown a down-conversion property where the Eu³⁺-activated ion was excited at 251 nm. Under the excitation of 251 nm, CBP/Eu phosphor showed intense emissions peaking at 591,617, and 693 nm due to the ⁵D₀ → ⁷F₁, ⁵D₀ → ⁷F₂, and ⁵D₀ → ⁷F₄ transition of Eu³⁺ ions. The obtained results suggest that the CBP/Eu phosphors have the potential for spectral response coating materials to improve photovoltaic (PV) panel efficiency.