This research investigates the effects of drying on some selected vegetables, which are Telfaria occidentalis, Amaranthu scruentus, Talinum triangulare, and Crussocephalum biafrae. These vegetables were collected fresh, sliced into smaller sizes of 0.5 cm, and dried in a convective dryer at varying temperatures of 60.0 °C, 70.0 °C and 80.0 °C respectively, for a regulated fan speed of 1.50 ms‒1, 3.00 ms‒1 and 6.00 ms‒1, and for a drying period of 6 hours. It was discovered that the drying rate for fresh samples was 4.560 gmin‒1 for Talinum triangulare, 4.390 gmin‒1for Amaranthu scruentus, 4.580 gmin‒1 for Talinum triangulare, and 4.640 gmin‒1 for Crussocephalum biafrae at different controlled fan speeds and regulated temperatures when the mass of the vegetable samples at each drying time was compared to the mass of the final samples dried for 6 hours. The samples are considered completely dried when the drying time reaches a certain point, as indicated by the drying rate and moisture contents tending to zero. According to drying kinetics, the rate of moisture loss was extremely high during the first two hours of drying and then steadily decreased during the remaining drying duration. The rate at which moisture was removed from the vegetable samples after the drying process at varying regulated temperatures was noted to be in this trend: 80.0 °C > 70.0 °C > 60.0 °C and 6.0 ms‒1 > 3.0 ms‒1 > 1.5 ms‒1 for regulated fan speed. It can be stated here that the moisture contents has significant effects on the drying rate of the samples of vegetables investigated because the drying rate decreases as the regulated temperatures increase and the moisture contents decrease. The present investigation is useful in the agricultural engineering and food engineering industries.

Solar energy is a reliable and abundant resource for both heating and power generation. The current research examines how the novel class of nano-embedded Bees wax phase change materials (NEBPCMs) improves heat storage qualities. The synthetic NEBPCMs were subjected to experimental testing using, XRD, Bees wax and Al2O3 FESEM. A typical solar water heating system features a flat plate collector unit incorporating Bees Wax phase change material (NEBPCM) combined with varying concentrations of Al2O3 (0.01%, 0.015%, and 0.02%). The absorber plate surface is coated with a Nano-hybrid coating consisting of Black Paint, Al2O3, and additional Fe3O4 at a 2% concentration. Pure water is frequently used in these solar water heaters (SWH), with performance evaluations conducted using different Bees Wax and Al2O3 concentrations of NEBPCM (Bees Wax + Al2O3). The system’s efficiency is assessed across different flow rates (60, 90, and 120 kg/hr) and tilt angles (15, 30, and 45 degrees). This study aims to examine the feasibility of using PCMs to store solar energy for night time water heating, ensuring a continuous supply of hot water maximum efficiency achieved by using NEBPCM in solar water heater 52.26% at a flow rate of 120 Kg/hr, at angle of 45 degrees and Concentration 0.015%.

The increased awareness of the environmental effects of petroleum based plastics has stimulated the coffee price emergence of biodegradable polymers such as polylactic acid (PLA). In a bid to increase the sustainability of PLA agricultural residues of animal feeds (corn stover, rice straw, and soybean hulls) have been explored and examined as reinforcing fillers to PLA composites. The consideration of such applications is suitable to the goals of the circular economy as it recycles low-value agricultural products. The current review critically evaluates lately carried out life cycle assessment (LCA) studies on PLA composites that have implemented such waste fillers with the full focus being on their environmental performance as well as methodological consistency. The review shows that these fillers have a potential of reducing the amount of greenhouse emission, energy usage, and other environmental effects, compared to pure PLA. However, unevenness in LCA methodology, especially in functional units, the system boundaries, and impacts categories obstructs direct LCA comparisons. The 1997 State of the Market report also has limited options of feedstocks and the lack of appraisals in the socio-economic front, so the overall sustainability analysis is restricted. Some of the remaining limitations that can be critical are to have generalized LCA frameworks, extended exploration of waste-based fillers, as well as combination of techno-economic analysis and social impact. Future inquiries ought to devise design considerations that would optimize both the functional characteristics and the performance of the environment and improve the reliability of sustainability measures. This review is evidence to the potential of agricultural waste reinforced PLA composites in the progress towards environmentally friendly materials and the need of integrative evaluation in the sustainable maturation of bioplastics.

This study examines the spatial distribution of socioeconomic conditions in Colombia, using Moran’s Index as a tool for spatial autocorrelation analysis. Key indicators related to education, health, infrastructure, access to basic services, employment, and housing conditions are addressed, allowing the identification of inequalities and structural barriers. The research reveals patterns of positive autocorrelation in several socioeconomic dimensions, suggesting a concentration of poverty and underdevelopment in certain geographic areas of the country. The results show that municipalities with more unfavorable conditions tend to cluster spatially, particularly in the northern, northwestern, western, eastern, and southern regions of the country, while the central areas exhibit better conditions. Permutation analyses are employed to validate the statistical significance of the findings, and LISA cluster maps highlight the regions with the highest concentration of poverty and social vulnerability. This work contributes to the literature on inequality and regional development in emerging economies, demonstrating that public policies should prioritize intervention in territories that exhibit significant spatial clustering of poverty. The methodology and findings provide a foundation for future studies on spatial correlation and economic planning in both local and international contexts.

It is proposed to use angular descriptors (in polar and Euler coordinates or quaternions), as well as radiation patterns of many variables, in HF radiofrequency and microwave thermal analysis of anisotropic systems.