The present work shows an application of the Chan-Vese algorithm for the semi-automatic segmentation of anatomical structures of interest (lungs and lung tumor) in 4DCT images of the thorax, as well as their three-dimensional reconstruction. The segmentation and reconstruction were performed on 10 CT images, which make up an inspiration-expiration cycle. The maximum displacement was calculated for the case of the lung tumor using the reconstructions of the onset of inspiration, the onset of expiration, and the voxel information. The proposed method achieves appropriate segmentation of the studied structures regardless of their size and shape. The three-dimensional reconstruction allows us to visualize the dynamics of the structures of interest throughout the respiratory cycle. In the future, it is expected to have more evidence of the good performance of the proposed method and to have the feedback of the clinical expert, since the knowledge of the characteristics of anatomical structures, such as their dimension and spatial position, helps in the planning of Radiotherapy (RT) treatments, optimizing the radiation dose to cancer cells and minimizing it in healthy organs. Therefore, the information found in this work may be of interest for the planning of RT treatments.

Potassium dihydrogen phosphate, KH2PO4 (KDP) crystal is an excellent electro-optical nonlinear optical crystal with large electro-optical nonlinear coefficient, high laser damage threshold, and laser frequency doubling effect, electro-optical effect , Piezoelectric effects and other special features, widely used in inertial confinement fusion engineering (ICF) and electro-optical switching devices. Therefore, its growth mechanism, growth process and performance have been systematically studied. In the process of KDP crystal growth, it is found that the stability of the growth solution is an important factor affecting the quality of crystal growth. Therefore, in recent years, more and more research on the stability of the solution, such as the study of ph, doping, supersaturation, overheating time on the stability of the solution. Among them, the research on the doping is mostly reported, and the research on this aspect is mainly focused on two aspects. On the one hand, it is the study of the stability of the solution under doping, and the other is the effect of doping on the optical quality of the crystal. In fact, the stability of the growth solution and the quality of crystal growth is directly related to the quality, but the existing research to isolate the two researches. Therefore, the experiment will be carried out in the case of double-doped KDP solution stability, KDP crystal growth and crystal optical quality and other experiments, and in-depth analysis of the impact of solution stability and crystal optical quality of the reasons, while the solution stability and The relationship between the optical quality of the crystal is briefly analyzed.

Numerical study of subcooled and saturated flow boiling in the curved and helically  coiled tubes in presence of phase change is one of the challenging area of CFD studies. In this paper, the CFD modeling of the nucleate and convective flow boiling in the small helically coiled tube at low vapor quality (up to the 18.93 percent) region is studied. A proper Eulerian-based mathematical model is used for interphase exchange forces and heat transfer between two phases in CFD modeling using Bulk boiling model. The results show that, the inner and the bottom wall of the helically coiled tube have the lowest and the highest heat transfer coefficient, respectively. The effect of change in coil diameter, helical pitch and tube diameter is investigated on the counters of vapor volume fraction. It is seen that at low vapor quality flows, the heat transfer coefficient is enhanced by decreasing in coil diameter, tube diameter and increasing in coil pitch of helically coiled tube. 

This work is a part of research on the microstructure and mechanical properties of Cr-Ni-Si steels after various thermal treatments [1, 2]. The need to minimize damage and losses caused by emerging failures in complex engineering facilities such as nuclear, thermal and hydroelectric power stations, and gas and oil pipelines necessitates the creation of materials of high strength, plasticity, welding and high rigidity.

Adsorption is a widely used method for the treatment of dissolved contaminants. Various agro-industrial wastes have been explored as potential adsorbents, showing high efficiency in dye removal. Each adsorbate-adsorbent pair needs kinetic, and equilibrium models to scale up this process. In this work, the equilibrium, kinetics and thermodynamics of the corn Tuza-Red 40 system were evaluated under batch system at ph = 2.0 at temperatures of 25, 40, and 55 °C. The Langmuir, Freundlich and Temkin models were selected for the isotherm representation, while the Lagergren, Ho, and Elovich equations for the kinetics of the process. The Freundlich model presented the best fit to the isotherms, the adsorption kinetics was best described by the Ho equation, and the values for Gibbs free energy and entropy indicated the spontaneity and feasibility of the process.

Plasma thermal gasification can be one of the most relevant and environmentally friendly technologies for waste treatment and has gained interest for its use in thethermos-conversion of biomass. In this perspective, the objective of this study is to evaluate the gasification of sugarcane bagasse by studying the effective areas of operation of this process and to establish a comparison with conventional autothermal gasification. A thermochemical equilibrium model was used to calculate the indicators that characterize the performance of the process on its own and integrated with a combined cycle. As a result, it was obtained that plasma and gasification of bagasse is technically feasible for the specific net electrical production of 4 MJ with 30 % electrical efficiency, producing a gas with higher calorific value than autothermal gasification. The operating points where the electrical energy production and the cold gas efficiency reach their highest values were determined; then the effects of the operational parameters on these performance indicators were analyzed.