The propagation of plant material in the arracacha crop is commonly done vegetatively through asexual seed, this activity has allowed its multiplication and conservation over time. The plant material available is of low quality, affecting the development and potential yield of the crop and therefore the producer’s income. The objective of the research was to comparatively analyze two technologies for the production of arracacha seed: local technology and Agrosavia technology. The information for the local technology was obtained from surveys applied to farmers and the selection was made using the deterministic sampling technique, and for the Agrosavia technology through the recording of data and production costs in research lots at commercial scale. Descriptive statistics and calculation of economic return indicators were applied for the two situations. The results show that the use of quality seed allows obtaining higher seed production (251,559 unit ha^-1) and tuberous roots (25,875 kg ha^-1), being superior to local technology by 14% and 28% respectively; thus, the arracacha producer acquires greater economic efficiency by obtaining lower unit cost per kilo produced and better net income with a marginal rate of return of 316.45. The results achieved are useful for farmers, companies and entities that wish to produce quality seed and support the arracacha production system in Colombia.

The performance of five cauliflower cultivars in conventional and alternative phytosanitary management—without the use of synthetic pesticides—was evaluated. Two experiments were conducted at Epagri, Ituporanga Experimental Station in February 2018 and 2019. A randomized block design with four repetitions was adopted, with twenty plants of each cultivar as plots. The seedlings were transplanted on millet and mucuna straw at a spacing of 0.5 m × 0.8 m. We evaluated agronomic yield, inflorescence quality, pest damage and plant diseases, especially bacterial and fungal rots. The cauliflower hybrids Vera, Verona and Serena stood out in productivity and quality, being the most indicated for sowing in off-season crops, in the Alto Vale do Itajaí region. The most productive cultivars were less damaged by bacterial diseases and defoliating caterpillars and without interference of whitefly infestation on yield. The results also reveal that it is possible to control pests and diseases with phytosanitary products of lower toxicity, i.e., with lower residues of synthetic pesticides.

One of the biggest environmental problems that has affected the planet is global warming, due to high concentrations of carbon (CO₂), which has led to crops such as coffee being affected by climate change caused by greenhouse gases (GHG), especially by the increase in the incidence of pests and diseases. However, carbon sequestration contributes to the mitigation of GHG emissions. The objective of this work was to evaluate the carbon stored in above and below ground biomass in four six-year-old castle coffee production systems. In a trial established under a Randomized Complete Block Design (RCBD) with the treatments Coffee at free exposure (T1), Coffee-Lemon (T2), Coffee-Guamo (T3) and Coffee-Carbonero (T4), at three altitudes: below 1,550 masl, between 1,550 and 2,000 masl and above 2,000 masl. Data were collected corresponding to the stem diameters of coffee seedlings and shade trees with which allometric equations were applied to obtain the carbon variables in the aerial biomass and root and the carbon variables in leaf litter and soil obtained from their dry matter. Highly significant differences were obtained in the four treatments evaluated, with T4 being the one that obtained the highest carbon concentration both in soil biomass with 100.14 t ha^-1 and in aerial biomass with 190.42 t ha^-1.

Apple farming is a new production venture across the North Shewa Zone. Its production, harvest, postharvest handling, and marketing status are not well known. This study was conducted to assess the above-lined situations across the district. Four representative locations, Asabahir, Tsigereda, Tengego, and Godnamamas were selected based on their apple production status. Then, a total of 88 respondents were randomly selected and interviewed by a structured questionnaire. The data were analyzed by descriptive statistics of percentage, standard deviation, and chi-square tests. A larger percentage of farmers are male (82.9%), in their active production age (41.7%), and produce apples in their backyard (85.25%). The agronomic management of fertilization, pruning, training, and plant spacing deviate from the recommended practices of apple farming. Whereas varietal distribution, irrigation, and post-harvest treatments are better practiced. Loss of fruits by fruit drops and discrimination on the market due to small fruit size are serious problems across the locations. Regarding apple farming, the farmers think of it as a productive venture and got a better price per kg and single fruit sale. They sell mainly in local collectors (60.2%) and nearby cities. As for institutional support, the farmers got apple seedlings, training, and capacity buildings by Agriculture Offices and NGOs, even if the farmers are still in higher need of better support. Therefore, it can be concluded that if not outwaited by poor tree management, destructive product transportation, and higher loss of fruits from trees and in the market, the attitude of the farmers can be capitalized in better production of apples.

Lean (also referred to as the Toyota Production System, TPS) is considered to be a radical alternative to the traditional method of mass production and batching principles for maximising operational efficiency, quality, speed and cost. Many hospitals inspired from lean manufacturing to develop their process. They had many improvements in their process. Hospitals reduced their patient waiting times, defects, wastes related to inventory, staff movement and patient transportation by implementing. This study utilizes scientometric and bibliometric tools to analyze visually the literature published in the field of medical lean manufacturing from 2009 to 2023. The relevant articles published from 2009 to 2023 were retrieved from the Web of Science Core Collection, VOSviewer and R software were used for bibliometric analysis and visualization. The number of publications related to the research has been increasing year by year before 2021, and then showed a downward trend, including 418 articles from 64 countries and regions, 743 institutions, 198 journals, and 1766 authors. The United States, Italy, and England are the main publishing countries in this research field. The journal “International Journal of Lean Six Sigma” published the most papers (n = 21) about lean manufacturing in medicine, the author with the most publications is Teeling SP, and the most influential author is Improta G. The top three keywords are “Healthcare”, “Quality improvement” and “Management”. This study provides a comprehensive bibliometric analysis of lean manufacturing in medicine, which can help researchers understand the current research hotspots in this field, explore potential research directions, and identify future development trends.

Shipbuilding industry is characterized by high price competition, as well as tight deadlines for product design and production. The dominant positions in the civil shipbuilding market are occupied by the countries of Southeast Asia, and for a number of reasons, participants from other countries are uncompetitive. Thus, in order to ensure the sustainable development of companies in the global civil shipbuilding market, it is necessary to identify and analyze the main factors that provided the competitive advantages of industry leaders. Assessment of further directions of shipbuilding development is a necessary condition for the formation of competitive advantages of new market participants. The article analyzes the main directions of development of the world civil shipbuilding in the period after World War II, as well as prospects for the future. As a result of the analysis of the latest organizational management concepts, the concept of modular production in shipbuilding is proposed, and directions for further research are determined.