COVID-19 and the economic response have amplified and changed the nature of development challenges in fundamental ways. Global development cooperation should adapt accordingly. This paper lays out the urgency for new methods of development cooperation that can deliver resource transfers at scale, oriented to addressing climate change and with transparency and better governance. It looks at what is actually happening to major donor countries’ development cooperation programs and where the principal gaps lie, and offers some thoughts on how to move forward, notwithstanding the clear geopolitical rivalries that are evident.
The most immediate challenge is to provide a level of liquidity support to countries ravaged by the global economic downturn. Many developing countries will see double-digit declines in GDP, with some recording downturns not seen in peacetime. Alongside the short-term challenge of recovery, COVID-19 has laid bare longer-term trends that have pointed for some time to the lack of sustainability—environmental, social, and governance—in the way economic development was occurring in many places, including in advanced economies. This new landscape has significant implications for development cooperation in terms of scale, development/climate co-benefits, and transparency and accountability.

In this paper, a series of Li₃V₂(PO₄)₃/C composite nanofibers is prepared by a facile and environmentally friendly electrospinning method and calcined under different temperatures. The LVP nanofiber calcined under 900 ℃ exhibits the best electrochemical performance. The bicontinuous morphologies of LVP/CNF are the fibers shrunk and the LVP crystals simultaneously grown. At the range of 3.0–4.3 V, LVP/CNF obtained under 900 ℃ delivers the initial capacity of 135 mAh/g, close to the theoretical capacity of LVP. Even at high current density, the sample of LVP/CNF still presents good electrochemical performance.

For five different regions in Kırklareli province, heavy metals; such as Pb, Ni, Cu, Mn, Cd, Cr, Co, Zn, Mo, and Fe in the mixture of leaves and flowers from linden trees (Tilia tomentosa L.) were analyzed by using flame atomic absorption spectroscopy after the samples were dissolved with microwave method. Also, organochloride pesticides; such as ∑BHC: [α-BHC, β-BHC, γ-BHC, and δ-BHC], ∑DDT: [4,4’-DDD, 4,4’-DDE, and 4,4’-DDT], α-Endosulfan, β-Endosulfan, Endosulfan sulfate, Heptachlor, Heptachlor-endo-epoxide, Aldrin, Dieldrin, Endrin aldehyde, Endrin ketone, Endrin and Methoxychlor in these samples were determined by utilizing gas chromatography mass spectroscopy after the samples were prepared for analyses by using QuEChERS method. The metal concentrations in the samples were in the range of 45.3 to 268 mg/kg for Mn, 0.25 to 18.8 mg/kg for Cu, 11.5 to 46.1 mg/kg for Zn, 128 to 1310 mg/kg for Fe, 10.4 to 38.6 mg/kg for Mo, 0.82 to 1.34 mg/kg for Cd, 0 to 6.45 mg/kg for Ni, 0 to 19.2 mg/kg for Pb, and 0 to 8.25 mg/kg for Cr. Moreover, the concentrations of organochloride pesticides in samples were usually determined to be lower than their maximum residue level values given the pesticide residue limit regulation of Turkish Food Codex. 

We report a method for effectively and homogeneously incorporating carbon nanotubes (CNTs) in the form of double-wall (DWCNTs) and multi-wall (MWCNTs) structures into commercial paints without the use of additives, surfactants, or chemical processes. The process involves the physical mixing of the nanotubes and polymers using the cavitation energy of an ultrasonic bath. It is a simple, fast method that allows for uniform distribution of carbon nanotube bundles within the polymer for direct application. Due to the hydrophobic properties of the carbon nanotubes as grown, we used paint samples containing 0.3% by mass of both types of CNTs and observed an improvement in waterproofing through wettability and water absorption through immersion tests on the samples. Different solvents such as water, formaldehyde, and glycerin were used, and the results showed an increase in paint impermeability of 30% and 25% with the introduction of DWCNTs and MWCNTs, respectively. This indicates a promising, economically viable, and revolutionary method for applying nanotechnology in the polymer industry.

The semiclassical boron–boron interatomic pair potential is constructed in an integral form allowing its converting into the analytical one. It is an ab initio B–B potential free of any semiempirical adjusting parameters, which would serve as an effective tool for the theoretical characterization of all-boron and boron-rich nanomaterials.

Nanotransformations of a blanket at the fair dimensional combined processing with imposing of electric field the tool in the form of untied metal granules are considered. An object of researches are the figurine details applied in aviation, the missile and space equipment and in the oil and gas industry: driving wheels and a flowing part of cases of turbo-pump units, screws, krylchatka where there are sites of variable curvature with limited access of the tool in a processing zone.It is shown that the combination in the combined process of two-component technological environments of current carrying granules and the electroconductive liquid environment given with a high speed to a processing zone allows to receive the required quality of a blanket; action of electric field from a source with the increased tension allows to create at fair dimensional processingthe required peening from blows of firm granules. It gives the chance to raise a resource and durability of responsible knots of the aerospace equipment and oil and gas equipment, to expand the field of use of the combined processing with untied granules on a detailwith the sitesnot available to processing by a profile electrode.