Water pollution has become a serious threat to our ecosystem. Water contamination due to human, commercial, and industrial activities has negatively affected the whole world. Owing to the global demanding challenges of water pollution treatments and achieving sustainability, membrane technology has gained increasing research attention. Although numerous membrane materials have focused, the sustainable water purification membranes are most effective for environmental needs. In this regard sustainable, green, and recyclable polymeric and nanocomposite membranes have been developed. Materials fulfilling sustainable environmental demands usually include wide-ranging polyesters, polyamides, polysulfones, and recyclable/biodegradable petroleum polymers plus non-toxic solvents. Consequently, water purification membranes for nanofiltration, microfiltration, reverse osmosis, ultrafiltration, and related filtration processes have been designed. Sustainable polymer membranes for water purification have been manufactured using facile techniques. The resulting membranes have been tested for desalination, dye removal, ion separation, and antibacterial processes for wastewater. Environmental sustainability studies have also pointed towards desired life cycle assessment results for these water purification membranes. Recycling of water treatment membranes have been performed by three major processes mechanical recycling, chemical recycling, or thermal recycling. Moreover, use of sustainable membranes has caused positive environmental impacts for safe waste water treatment. Importantly, worth of sustainable water purification membranes has been analyzed for the environmentally friendly water purification applications. There is vast scope of developing and investigating water purification membranes using countless sustainable polymers, materials, and nanomaterials. Hence, value of sustainable membranes has been analyzed to meet the global demands and challenges to attain future clean water and ecosystem.

In this study, robust and defect-free thin film composite (TFC) forward osmosis (FO) membranes have been successfully fabricated using ceramic hollow fibers as the substrate. Polydopamine (PDA) coating under controlled conditions is effective in reducing the surface pores of the substrate and making the substrate smooth enough for interfacial polymerization. The pure water permeability (A), solute permeability (B), and structural parameter (S) of the resultant FO membrane are 0.854 L·m^–2·h⁻¹·bar⁻¹ (LMH/Bar), 0.186 L·m^–2·h⁻¹ (LMH), and 1720 µm, respectively. The water flux and reverse draw solute flux are measured using NaCl and proprietary ferric sodium citrate (FeNaCA) draw solutions at low and high osmotic pressure ranges. As the osmotic pressure increases, a higher water flux is obtained, but its increase is not directly proportional to the increase in the osmotic pressure. At the membrane surface, the effect of dilutive concentration polarization is much less serious for FeNaCA-draw solutions. At an osmotic pressure of 89.6 bar, the developed TFC membrane generates water fluxes of 11.5 and 30.0 LMH using NaCl and synthesized FeNaCA draw solutions. The corresponding reverse draw solute flux is 7.0 g·m^–2·h⁻¹ (gMH) for NaCl draw solution, but it is not detectable for FeNaCA draw solution. This means that the developed TFC FO membranes are defect-free and their surface pores are at the molecular level. The performance of the developed TFC FO membranes is also demonstrated for the enrichment of BSA protein.

In recent years, using novel nanomaterials to improve the antifouling and antibacterial performance of reverse osmosis membranes has received much attention. In this study, hydrophilic Ag@ZnO-hyperbranched polyglycerols nanoparticles were fabricated by ring-opening multibranched polymerization of glycidyl acid with the core-shell Ag@ZnO nanoparticles. The cellulose triacetate composite membranes were prepared by grafting Ag@ZnO-HPGs nanoparticles on the surface of cellulose triacetate membranes. The surface of the nanoparticles with active functional group –OH was confirmed by X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. Surface morphology, charge, and hydrophilicity of the composite membranes were characterized by scanning electron microscope, zeta potential, and contact angle analysis. The results showed that grafting the Ag@ZnO-HPGs nanoparticles onto the cellulose triacetate membrane surface improved the physical and chemical properties of the cellulose triacetate composite membranes. The water flux of cellulose triacetate composite membranes increased while the salt rejection rate to NaCl slightly decreased. Meanwhile, the cellulose triacetate composite membranes showed excellent antifouling properties of having a high flux recovery. The antibacterial performance of the cellulose triacetate composite membrane against E. coli and S. aureus was prominent that the antibacterial rates were 99.50% and 92.38%, and bacterial adhesion rates were as low as 19.12% and 21.35%, respectively.

In view of the large energy consumption of the regeneration process in the chemical absorption decarburization process, on the basis of the enrichment classification flow process, the nanoscale ceramic film is used as a new heat exchanger between the enriched liquid and the regeneration gas. The porous ceramic film is capable of coupling thermal-mass transfer to effectively recover part of the water vapor and the heat carried in the regeneration gas, so as to reduce the regenerative energy consumption of the system. The effects of parameters such as regeneration temperature, flow rate, molar fraction of water vapor, and MEA enrichment temperature, flow rate, and MEA concentration of shunt on the hydrothermal recovery effect of ceramic membranes of different pore sizes and lengths were studied by using the heat recovery flux and water recovery rate as the indicators. The results show that the hydrothermal recovery performance of the ceramic membrane increases with the increase of MEA enrichment flow, but decreases significantly with the increase of the enrichment temperature. At the same time, with the increase of regenerative gas velocity and the molar fraction of water vapor in the regenerative gas, the heat recovery flux will increase. The heat recovery performance of the 10 nm ceramic membrane is better than that of the 20 nm ceramic membrane.

In this paper, we deal with one of the most urgent and relevant topics nowadays, i.e., water pollution. The problem is finding a valid candidate for the absorption and removal of different kinds of pollutants commonly found in water. There are already some indications about graphene oxide as a potential candidate. In the present work, we take a step forward to show how graphene nanoplatelets (rather than the oxide form of this material) are capable of decontaminating water. In this starting step, we use a specific substance as a model pollutant, i.e., acetonitrile, leaving for the future steps, to extend the analysis to additional types of pollutants. In addition to laboratory-produced graphene nanoplatelets, we already examined in the past; now we wish to consider also commercially available ones, so that the new results will not be bound to a laboratory (low technology readiness level) material, but will become interesting also from the industrial point of view, thanks to the scalability of the nanoplatelets production. For this aim, we compare the performance of two types of filters based on two classes of nanomaterials, i.e., those produced by microwave and ultrasound assisted exfoliation, already analyzed in our earlier works, with those commercially distributed by an Italian company, i.e., NANESA, http://www.nanesa.com/. The latter is an innovative SME involved in the production of graphene-based nanomaterials. We focus here in the graphene nanoplatelets, commercially available in industrial batches (GXNan grades). The present study leads to determine which filtering membrane, among the various types of commercial graphene considered, shows the greatest stability, and the lack of breakage of the membrane, concentrating on such accessory features, given that all types of graphene showed excellent adsorption properties.