In this paper, an improved mathematical model for flashover behavior of polluted insulators is proposed based on experimental tests. In order to determine the flashover model of polluted insulators, the relationship between conductivity and salinity of solution pollution layer of the insulator is measured. Then, the leakage of current amplitude of four common insulators versus axial, thermal conductivity and arc constants temperature was determined. The experimental tests show that top leakage distance (TLd) to bottom leakage distance (BLd) ratio of insulators has a significant effect on critical voltage and current. Therefore, critical voltage and current were modeled by TLd to BLd ratio Index (M). Also, salinity of solution pollution layer of the insulators has been applied to this model by resistance pollution parameter. On the other hand, arc constants of each insulator in new model have been identified based on experimental results. Finally, a mathematical model is intended for critical voltage against salinity of solution pollution layer of different insulators. This model depends on insulator profile. There is a good agreement between the experimental tests of pollution insulators obtained in the laboratory and values calculated from the mathematical models developed in the present study.

To investigate the possible role of arbuscular mycrrhizal fungi (AMF) in alleviating the negative effects of salinity on Stevia rebaudiana (Bert.), the regenerated plantlets in tissue culture was transferred to pots in greenhouse and inoculated with Glomus intraradices. Salinity caused a significant decrease in chlorophyll content, photosynthesis efficiency and enhanced the electrolyte leakage. The use of AMF in salt –affected plants resulted in improved all above mentioned characteristics. Hydrogen peroxide and malondialdehyde (MDA) contents increased in salt stressed plants while a reduction was observed due to AMF inoculation. CAT activity showed a significant increase up to 2 g/l and then followed by decline at 5 g/l NaCl in both AMF and non-AMF treated stevia, however, AMF inoculated plants maintained lower CAT activity at all salinity levels (2 and 5 g/l). Enhanced POX activities in salt- treated stevia plants were decreased by inoculation of plants with AMF. The addition of NaCl to stevia plants also resulted in an enhanced activity of SOD whilst, AMF plants maintained higher SOD activity at all salinity levels than those of non-AMF inoculated plants. AMF inoculation was capable of alleviating the damage caused by salinity on stevia plants by reducing oxidative stress and improving photosynthesis efficiency. 

Bangladesh’s coastal regions are rich in saline water resources. The majority of these resources are still not being used to their full potential. In the southern Bangladeshi region of Patuakhali, research was conducted to investigate the effects of mulching and drip irrigation on tomato yield, quality, and blossom-end rot (BER) at different soil salinity thresholds. There were four distinct treatments applied: T₁= drip irrigation with polythene mulch, T₂ = drip irrigation with straw mulch, T₃ = drip irrigation without mulch, and T₄ = standard procedure. While soil salinity was much greater in treatment T₃ (1.19–8.42 dS/m) fallowed by T₄ (1.23–8.63 dS/m), T1 treatments had the lowest level of salinity and the highest moisture retention during every development stage of the crops, ranging from 1.28–4.29 dS/m. Treatment T₃ exhibited the highest soil salinity levels (ranging from 1.19 to 8.42 dS/m), followed by T₄ with a range of 1.23 to 8.63 dS/m. In contrast, T₁ treatments consistently maintained the lowest salinity levels (ranging from 1.28 to 4.29 dS/m) and the highest moisture retention throughout all stages of crop development. In terms of yield, drip irrigation with no mulch treatment (T₃) provided the lowest output (13.37 t/ha), whereas polyethylene mulching treatment (T₁) produced the maximum yield (46.04 t/ha). According to the study, conserving moisture in tomato fields and reducing soil salinity may both be achieved with drip irrigation combined with polythene mulch. The research suggests that employing drip irrigation in conjunction with polythene mulch could effectively preserve moisture in tomato fields and concurrently decrease soil salinity.