The characteristics of agricultural products are influenced by the ecosystem, from the perspective of biotic and abiotic factors, which produce in the plant physiological responses and in turn in the fruit unique physicochemical properties, which are the basis for designations of origin and strategies to add value to the product in the current market. In the present work, ten cocoa materials (Theobroma cacao L.) were selected for their outstanding productivity (FSV41, FLE3, FEAR5, FSA12, FEC2, SCC23, SCC80, SCC55, ICS95 and CCN51), which were established in the departments of Santander (931 m a.s.l.), Huila (931 m a.s.l.), Huila (931 m a.s.l.), Huila (931 m a.s.l.), Huila (931 m a.s.l.), Huila (931 m a.s.l.) and Huila (931 m a.s.l.). These were established in the departments of Santander (931 m a.s.l.), Huila (885 m a.s.l.) and Arauca (204 m a.s.l.), the main cocoa-producing areas in Colombia. For the evaluation of the physical characteristics of the collected materials, 21 quantitative descriptors were used to determine the physical variability of the fruit according to clone and place of collection. The data collected were analyzed by means of Pearson’s correlation matrix and principal component analysis, it was possible to identify those descriptors that contribute most to the variability among materials (ear index, diameter length ratio, seed weight and diameter, and fruit weight and length). In addition, it was possible to verify the effect of the place of harvest on the physical characteristics of the materials, high-lighting the importance of the adaptation study prior to the planting of the cocoa material, with the objective of guaranteeing a premium, productive and quality cocoa crop for the industry, which is competitive in the market.

The study of the performance of high-efficiency heat pump systems has been a hot issue of general interest in the field of heat pump air conditioning. For the designed and developed two-stage casing tandem heat exchanger of heat pump system, the 3D finite volume method and the realizable k-ε model are used to numerically analyze the influence law of inlet fluid temperature and flow velocity on the overall heat transfer coefficient as well as the Nussle number of inner and outer tubes. The results show that decreasing the inlet water temperature or increasing the inlet refrigerant temperature can improve the overall heat transfer performance; Nu_in increases with the increase of water and refrigerant flow rates, while Nu_out increases with the increase of water flow rate but decreases with the increase of refrigerant flow rate; Nu_in and Nu_out both increase with the decrease of water temperature or refrigerant temperature increases.

Introduction: The selection of genotypes with determinate growth habit in tomato should contemplate adequate selection criteria to increase the efficiency of the breeding program. Objective: The objective of this work was to estimate selection criteria for “chonto” type tomato lines with determined growth habit. Materials and methods: This work was carried out at the Universidad Nacional de Colombia (Palmira Campus), in 2016, with seven lines with determinate growth habit and a control with indeterminate growth. Heritability in a broad sense (h² g), coefficient of environmental variation, coefficient of genetic variation, selection efficiency and genetic gain were determined in parameters of morphological, phonological, fruit quality, fruit shape and production, using the RELM/BLUP procedure of the SELEGEN software. Results: There were three ranges of h² g, the first with values of h² g greater than 0.76, the second between 0.53 and 0.38, and the third with a value less than 0.38. The highest values of h² g were for final plant height with 0.92, plant height at harvest with 0.88, yield per plant with 0.83, days to flowering with 0.83, number of fruits per plant with 0.82, and days to harvest with 0.82. For genetic gain it was found that the control had the highest values for final plant height, plant height at harvest, internode length, days to harvest, harvest duration, soluble solids content, number of fruits per plant, fruit weight and yield per plant; however, in some parameters such as height and phenology for selection by determined growth habit, the lowest values were better. Conclusion: There was evidence of genetic parameters that could be considered as selection criteria for “chonto” type tomato lines with determinate growth habit.

The danger of riverbed processes is considered. Their speed varies from the first few months of the flood to the most dynamic process in nature. It happened in front of people. This may make life on the river bank and the utilization of river resources more difficult. This paper introduces the causes and consequences of the danger performance of riverbed processes, and focuses on the mapping methods of the danger assessment of riverbed processes: determining the danger degree of riverbed processes and different methods of displaying it on the map. An example of displaying danger on the previously drawn map is given, and the distribution of different types and expression degrees of dangerous riverbed processes under various natural conditions in Russia is briefly analyzed.

Electrospinning nanofiber membrane has the advantages of wide raw materials, large specific surface area, and high porosity. It is an ideal separator material for lithium-ion batteries. This paper first introduces two common electrospinning nanofiber diaphragms: polymer, polymer, and inorganic composite, and then focuses on the modification methods of composite modification, blending modification, and inorganic modification, as well as the methods of electrospinning nano modified polyolefin diaphragm. Finally, the development direction of the electrospinning lithium-ion battery separator has prospected.

The xanthorrhiza species of the genus Arracacia belongs to the Apiaceae family and is known for its ability to generate tuberous reservoir roots that are harvested annually and marketed fresh in South American countries such as Colombia, Brazil, Venezuela, Peru, Bolivia and Ecuador. In Colombia, arracacha is planted mainly in 15 departments and the regional cultivars are differentiated by the color of the leaves, petiole and tuberous root, the best known being amarilla común or paliverde, yema de huevo, and cartagenera. There are studies that have characterized regional materials by applying a limited number of descriptors, but they do not allow knowing the morphology and phenotypic differentiation of each one; therefore, their definition and characterization constitute a support in breeding programs that allow the efficient use of the genetic potential and increase the knowledge about the diversity of cultivars. Phenotypic characterization and description of three cultivars was performed during two production cycles (2016 and 2018) in two phases (vegetative and productive) applying 74 morphological variables (42 qualitative and 32 quantitative) organized in seven groups of variables: plant, leaf, leaflet, petiole, propagule, stock and tuberous root. A factorial analysis for mixed data (FAMD) was performed, which incorporated a multivariate analysis with all variables and identified 11 discriminant variables, 8 qualitative and 3 quantitative, which can be used in processes of characterization of arracacha materials. A morphological description of each cultivar was made, which means that this is the first complete characterization study of regional arracacha materials in Colombia.