The COVID-19 pandemic has shifted education from traditional in-person classes to remote, online-dependent learning, often resulting in reduced learning effectiveness and satisfaction due to limited face-to-face interaction. To address these challenges, interactive teaching strategies, such as the flipped classroom approach, have gained attention. The flipped classroom model emphasizes individual preparation outside class and collaborative learning during class time, relying heavily on in-person interactions. To adapt this method to remote learning, the Remote Flipped Classroom (RFC) integrates the flipped classroom approach with online learning, allowing flexibility while maintaining interactive opportunities. RFC has incorporated short films as teaching tools, leveraging their ability to contextualize knowledge and cater to the preferences of visually-driven younger learners. However, research on the effectiveness of RFC with films remains limited, particularly in fields like nursing education, where practical engagement is crucial. This article shares the practical experience of applying RFC with films in a nursing education context. Positive feedback was observed, though many students still expressed a preference for in-person classes. These insights suggest that strategies like RFC with films could be valuable in maintaining engagement and learning efficiency in remote classrooms.

In this study, robust and defect-free thin film composite (TFC) forward osmosis (FO) membranes have been successfully fabricated using ceramic hollow fibers as the substrate. Polydopamine (PDA) coating under controlled conditions is effective in reducing the surface pores of the substrate and making the substrate smooth enough for interfacial polymerization. The pure water permeability (A), solute permeability (B), and structural parameter (S) of the resultant FO membrane are 0.854 L·m^–2·h⁻¹·bar⁻¹ (LMH/Bar), 0.186 L·m^–2·h⁻¹ (LMH), and 1720 µm, respectively. The water flux and reverse draw solute flux are measured using NaCl and proprietary ferric sodium citrate (FeNaCA) draw solutions at low and high osmotic pressure ranges. As the osmotic pressure increases, a higher water flux is obtained, but its increase is not directly proportional to the increase in the osmotic pressure. At the membrane surface, the effect of dilutive concentration polarization is much less serious for FeNaCA-draw solutions. At an osmotic pressure of 89.6 bar, the developed TFC membrane generates water fluxes of 11.5 and 30.0 LMH using NaCl and synthesized FeNaCA draw solutions. The corresponding reverse draw solute flux is 7.0 g·m^–2·h⁻¹ (gMH) for NaCl draw solution, but it is not detectable for FeNaCA draw solution. This means that the developed TFC FO membranes are defect-free and their surface pores are at the molecular level. The performance of the developed TFC FO membranes is also demonstrated for the enrichment of BSA protein.

The silver nanoparticles (AgNPs) exhibit unique and tunable plasmonic properties. The size and shape of these particles can manipulate their localized surface plasmon resonance (LSPR) property and their response to the local environment. The LSPR property of nanoparticles is exploited by their optical, chemical, and biological sensing. This is an interdisciplinary area that involves chemistry, biology, and materials science. In this paper, a polymer system is used with the optimization technique of blending two polymers. The two polymer composites polystyrene/poly (4-vinylpyridine) (PS/P4VP) (50:50) and (75:25) were used as found suitable by their previous morphological studies. The results of 50, 95, and 50, 150 nm thicknesses of silver nanoparticles deposited on PS/P4VP (50:50) and (75:25) were explored to observe their optical sensitivity. The nature of the polymer composite embedded with silver nanoparticles affects the size of the nanoparticle and its distribution in the matrix. The polymer composites used are found to have a uniform distribution of nanoparticles of various sizes. The optical properties of Ag nanoparticles embedded in suitable polymer composites for the development of the latest plasmonic applications, owing to their unique properties, were explored. The sensing capability of a particular polymer composite is found to depend on the size of the nanoparticle embedded in it. The optimum result has been found for silver nanoparticles of 150 nm thickness deposited on PS/P4VP (75:25).

In order to understand the finishing effect of Waterborne Acrylic Paint under different painting methods and amount, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint, then the effects of different painting methods and amount on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Further, the mechanism of film formation was described by thermal property analysis using thermogravimetry and differential scanning calorimeter. The results show that different painting methods have little effect on film properties, the drying time of primer and topcoat are not affected by them, which is 8/8.5 min for primer surface/solid and 6.5/7 min for topcoats. The film surface hardness and adhesion can reach B and 0 grade, the best wear resistance of the film is 51.24 mg·100 r⁻¹ when using one-layer primer one-layer topcoat. Different coating amount has great influence on film properties, the drying speed of the film increases with the increase of the painting amount. The film properties reach the best when the painting amount is 80 g/m², while too little painting amount leads to the decrease of hardness, and too much leads to the wear resistance weaken. Thermal analysis of the primer and topcoat show that water decomposition occurs at 100 ℃ and thermal decomposition of organic components occur at 350 ℃. Topcoats have better thermal stability than primers higher than that of topcoat, the topcoat displayed better thermal stability than the primer.

This report deals synthesis of CuInGa (CIG) nano materials along with doctor blade and spin coated thin films selenization and their physical properties. The doctor blade and spin coated CIGS/SLG thin films thicknesses are obtained ̴ 2 μm and ̴ 2.95 μm.  Raman spectroscopy of these thin films leads the chalcopyrite phase formation by exhibiting the peak at wave number 171 cm^-1. The well developed grain growths of spin coated thin film are appeared in the surface morphology. While the grain growths developments in doctoral blade coated thin film is rather hard and fuzzy. EDS measurement recognised the existence of the compositional ratio presence of the alloying elements Cu, In. Ga and Se. The doctor blade and spin coated CIGS/SLG thin films are exhibited the UV- Visible transmission peak in the wave length range 240 nm 320 nm. The optical energy band gaps for the doctor blade and spin coated CIGS thin films are obtained 1.41eV and 1.5 eV.        

In this study, the effect of porogenic solvents on pore size distribution of the polycaprolactone (PCL) thin films was investigated. Five thin PCL films were prepared using the solvent-casting method. Chloroform, Methylene Chloride (MC) and three different compositions of MC/ Dimethylformamide (DMF) (80/20, 50/50 and 20/80) were used as solvents. Scanning Electron Microscopy (SEM) investigations were employed to study morphology and consequently the pore size distribution of the prepared films. The PCL films made by chloroform and MC as a solvent were completely non-porous. Whereas the other films (made by a combination of MC and DMF) showed both uni-modal and bi-modal pore size distributions.