The importance of improving industrial transformation processes for more efficient ones is part of the current challenges. Specifically, the development of more efficient processes in the production of biofuels, where the reaction and separation processes can be intensified, is of great interest to reduce the energy consumption associated with the process. In the case of Biodiesel, the process is defined by a chemical reaction and by the components associated to the process, where the thermochemical study seeks to develop calculations for the subsequent understanding of the reaction and purification process. Thus, the analysis of the mixture of the components using the process simulator Aspen Plus V9^® unravels the thermochemical study. The UNIFAC-DMD thermodynamic method was used to estimate the binary equilibrium parameters of the reagents using the simulator. The analyzed aspects present the behavior of the components in different temperature conditions, the azeotropic behavior and the determined thermochemical conditions.

Four alloys based on niobium and containing about 33wt.%Cr, 0.4wt.C and, in atomic content equivalent to the carbon one, Ta, Ti, Hf or Zr, were elaborated by classical foundry under inert atmosphere. Their as-cast microstructures were characterized by X-ray diffraction, electron microscopy, energy dispersion spectrometry and while their room temperature hardness was specified by Vickers indentation. The microstructures are in the four cases composed of a dendritic Nb-based solid solution and of an interdendritic NbCr₂ Laves phase. Despite the MC-former behavior of Ta, Ti, Hf and Zr usually observed in nickel or cobalt-based alloys, none of the four alloys contain MC carbides. Carbon is essentially visible as graphite flakes. These alloys are brittle at room temperature and hard to machine. Indentation shows that the Vickers hardness is very high, close to 1000HV_10kg. Indentation lead to crack propagation through the niobium phase and the Laves areas. Obviously no niobium-based alloys microstructurally similar to high performance MC-strengthened nickel-based and cobalt-based can be expected. However the high temperature mechanical and chemical properties of these alloys remain to be investigated.

In this study, we utilized a convolutional neural network (CNN) trained on microscopic images encompassing the SARS-CoV-2 virus, the protozoan parasite “plasmodium falciparum” (causing of malaria in humans), the bacterium “vibrio cholerae” (which produces the cholera disease) and non-infected samples (healthy persons) to effectively classify and predict epidemics. The findings showed promising results in both classification and prediction tasks. We quantitatively compared the obtained results by using CNN with those attained employing the support vector machine. Notably, the accuracy in prediction reached 97.5% when using convolutional neural network algorithms.

Introduction: Stenoses in the path of arteriovenous fistulas (AVF) for hemodialysis are a very prevalent problem and there is long experience in their treatment by percutaneous angioplasty (PTA). These procedures, however, involve non-negligible equipment requirements, exposure to radiation and intravenous contrast that are not beneficial for the patient and make their performance more complex. This study reviews our initial experience with Doppler ultrasound-guided angioplasty. Methods: Prospective cohort of patients with native AVF dysfunction due to significant venous stenosis treated by Doppler echo-guided PTA. AVF puncture, lesion catheterization, balloon localization and inflation, and outcome verification were performed under ultrasound guidance. Only one fistulography was performed before and another one after dilatation. As a control, the cases performed during the same period by the usual angiographic method were also collected. Results: Between February 2015 and September 2018, 51 PTAs were performed on native AVF, of which 27 were echogenic (mean age, 65.3 years; 63% male). The technical success rate was 96%. In 26% of cases, PTA was repeated due to residual stenosis after angiographic imaging. There were 7.3% periprocedural complications. 92% of the AVFs were punctured at 24 hours. Primary patency at 1 month, 6 months and 1 year was 100%, 64.8% and 43.6%, and assisted patency was 100%, 87.2% and 74.8%. There were no significant differences in immediate or late results with respect to angiographically guided AVF angioplasty. Conclusions: AVF-PTA can be performed safely and effectively guided by Doppler ultrasound, which simplifies the logistics required for its performance, although we still need to improve the capacity for early verification of the result with this imaging technique.

Heat recovery is one of the measures proposed for the appropriate use of ammonia in tropical countries. This article analyzes a heat recovery system installed in an industrial refrigeration plant. Based on comparative readings of operating parameters of the installation, determined the effectiveness of the heat exchange, the increase in the efficiency of the refrigeration system, as well as the fuel saved by heating water in the industry. The results obtained reported that the thermal design based on heat exchange in annular spaces allows a significant saving of resources and a high rate of thermal utilization.

Introduction: The selection of genotypes with determinate growth habit in tomato should contemplate adequate selection criteria to increase the efficiency of the breeding program. Objective: The objective of this work was to estimate selection criteria for “chonto” type tomato lines with determined growth habit. Materials and methods: This work was carried out at the Universidad Nacional de Colombia (Palmira Campus), in 2016, with seven lines with determinate growth habit and a control with indeterminate growth. Heritability in a broad sense (h² g), coefficient of environmental variation, coefficient of genetic variation, selection efficiency and genetic gain were determined in parameters of morphological, phonological, fruit quality, fruit shape and production, using the RELM/BLUP procedure of the SELEGEN software. Results: There were three ranges of h² g, the first with values of h² g greater than 0.76, the second between 0.53 and 0.38, and the third with a value less than 0.38. The highest values of h² g were for final plant height with 0.92, plant height at harvest with 0.88, yield per plant with 0.83, days to flowering with 0.83, number of fruits per plant with 0.82, and days to harvest with 0.82. For genetic gain it was found that the control had the highest values for final plant height, plant height at harvest, internode length, days to harvest, harvest duration, soluble solids content, number of fruits per plant, fruit weight and yield per plant; however, in some parameters such as height and phenology for selection by determined growth habit, the lowest values were better. Conclusion: There was evidence of genetic parameters that could be considered as selection criteria for “chonto” type tomato lines with determinate growth habit.