In this paper, electrically conductive composites comprised of silicone rubber and titanium diboride (TiB₂) were synthesized by conventional mixing methods. Fine particles of TiB₂ (in micron size) and 10 parts per hundred parts of rubber (phr) proportion of carbon black (XC-72) were used to make the composites with HTV silicone rubber. The composites were cured at appropriate temperature and pressure and the effect on the electrical properties was studied. The resistance of the silicone rubber is ~ 10¹⁵Ω which decreases to 1–2 kΩ in case of composites with negligible effect of heat ageing. The hardness increases by ~ 35% simultaneous to the decrease of ~ 47% in the tensile strength. Morphological characterization indicates the homogeneous dispersion of the fillers in the composite.

Nanoparticle V₂O₅ is prepared by the measurement of X-ray diffraction (XRD) and atomic force microscopy (AFM) analyses. The crystallite size = 19.59 nm, optical energy gap = 2.6 eV, an average particle size of 29.58 nm and, RMS roughness of ~6.8 nm. Also, Fourier transformer infrared spectrophotometer (FTIR) showed a porous free morphology with homogeneity and uniformity on the sample surface. The film surface exhibited no apparent cracking and, the grains exhibited large nicely separated conical columnar growth combined grains throughout the surface with coalescence of some columnar grains at a few places. The fabrication of a thin film of V₂O₅ NPs/PSi heterojunction photodetector was characterized and investigated.

Ce⁴⁺-doped nanometer ZnO powder was synthesized by so-l gel method. The microstructures and properties of the samples were characterized through XRD, UV-Vis and FTIR. The results indicated that the Ce⁴⁺ was successfully incorporated into ZnO, and the diameter of the nanometer was about 10.7nm. It induced the redshifting in the UV-Vis spectra. The photocatalytic activity of the samples was investigated using methylene blue (MB) as the model reaction under irradiation with ultraviolet light. The results showed that the doping of Ce⁴⁺ could increase the photocatalytic activities of ZnO nanopowders and that the best molar ratio of Ce⁴⁺ was n(Ce)/n(Zn) = 0.05, that the surfactant was sodium dodecyl sulfate, and that the nanometer ZnO was calcinated at 550 ℃ for 3 hours. Meanwhile, it inspected the effect of photocatalytic efficiency through the pH of MB, the amount of catalyst, and illumination time. The experimental results revealed that the initial mass concentration of MB was 10 mg/L, that the pH value was 7-8, that the dosage of Ce⁴⁺/ZnO photo-catalyst was 5 g/L, that the UV-irradiation time was 2 h, and that the removal rate of MB reached above 85%. Under the optimized conditions, the degradation rate of real dye wastewater was up to 87.67% and the removal efficiency of COD was 63.5%.

Disease epidemics may spread quickly and easily throughout nations and continents in our current global environment, having a devastating effect on public health and the world economy. There are over 513 million people worldwide who have been infected, and more than 6.2 million have died due to SARS-CoV-2. There are treatments but no cures for most viruses. Nevertheless, the spread of viruses can be limited by introducing antiviral coatings on public area surfaces and personal protective equipment (e.g., face masks). This work aims to fabricate a polymer-based coating with acrylic resin as a binder that possesses great antiviral activity against the Feline coronavirus (FCov). The chosen polymer, polyethylene glycol (PEG), is used as an antiviral agent because it contains “green” chemistry benefits such as non-toxicity, being inexpensive, readily recyclable, safe, natural, non-flammable, biocompatible, and biodegradable. The PEG/acrylic coating systems of different weight percentages were coated on the glass substrates by the spray-coating method and cured at room temperature for 24 hours. The developed PEG/acrylic coating system that contains 20 wt% of PEG exhibits the highest anti-viral activities (99.9% against FCov) compared to the other weight percentages. From this study, it has been observed that the hydrophilicity of the coating plays an important role in its antiviral activity. The developed coating has a hydrophilic property, in which the contact angle was measured at 83.28 ± 0.5°. The FTIR reveals that there are no existing toxic components or new components contained in the coating samples.

Metal organic framework is a class of hybrid network of supramolecular solid materials comprised of a large number of inorganic and organic linkers all bounded to metal ions in a well-organized fashion. This type of compounds possess a greater surface area with an advantage of changing pore sizes, diversified and beautiful structure which withdrew an intense interest in this field. In the present review articles, the structural aspects, classification, methods of synthesis, various factors affecting the synthesis and stability, properties and applications have been discussed. Recent advances in the field and new directions to explore the future scope and applications of MOFs have been incorporated in this article to provide current status of the field.

An α, α^′-dipyridyl adduct of a complex compound hexaaquatribenzene-1,2,4,5-tetracarbonatotetra iron (III) with porous structure was synthesized for the first time. According to the results of elemental, X-ray, IR-spectroscopic and differential-thermal analyses the individuality, chemical formula, thermal destruction, and form of coordination of acidic anion and dipyridyl were established. During interaction of a complex compound with dipyridyl, it completely loses all crystallization molecule of water resulting in a compound with a chemical formula of Fe₄(C₆H₂(COO)₄)₃(dpy)₂(dipyridyl). Using the identification of diffraction pattern the parameters of lattice cell of the complex compound were determined.