Four alloys based on niobium and containing about 33wt.%Cr, 0.4wt.C and, in atomic content equivalent to the carbon one, Ta, Ti, Hf or Zr, were elaborated by classical foundry under inert atmosphere. Their as-cast microstructures were characterized by X-ray diffraction, electron microscopy, energy dispersion spectrometry and while their room temperature hardness was specified by Vickers indentation. The microstructures are in the four cases composed of a dendritic Nb-based solid solution and of an interdendritic NbCr₂ Laves phase. Despite the MC-former behavior of Ta, Ti, Hf and Zr usually observed in nickel or cobalt-based alloys, none of the four alloys contain MC carbides. Carbon is essentially visible as graphite flakes. These alloys are brittle at room temperature and hard to machine. Indentation shows that the Vickers hardness is very high, close to 1000HV_10kg. Indentation lead to crack propagation through the niobium phase and the Laves areas. Obviously no niobium-based alloys microstructurally similar to high performance MC-strengthened nickel-based and cobalt-based can be expected. However the high temperature mechanical and chemical properties of these alloys remain to be investigated.

In this study, the development of rinnenkarren systems is analyzed. During the field studies, 36 rinnenkarren systems were investigated. The width and depth were measured at every 10 cm on the main channels and then shape was calculated to these places (the quotient of channel width and depth). Water flow was performed on artificial rinnenkarren system. A relation was looked for between the density of tributary channels and the average shape of the main channel, between the distance of tributary channels from each other and the shape of a given place of the main channel. The density and total length of the tributary channels on the lower and upper sections of the main channels being narrow at their lower end (11 pieces) and being wide at their lower end (10 pieces) of the rinnenkarren systems were calculated as well as their average proportional distance from the lower end of the main channel. The number of channel hollows was determined on the lower and upper sections of these main channels. It can be stated that the average shape of the main channel calculated to its total length depends on the density of the tributary channels and on the distance of tributary channels from each other. The main channel shape is smaller if less water flows on the floor for a long time because of the small density of the tributary channels and the great distance between the tributary channels. In this case, the channel deepens, but it does not widen. The width of the main channel depends on the number and location of the rivulets developing on channel-free relief. The main channel becomes narrow towards its lower end if the tributary rivulets are denser and longer on the upper part of the main rivulet developing on the channel-free, plain terrain and their distance is larger compared to the lower end. The channel hollows develop mainly at those places where the later developing tributary channels are hanging above the floor of the main channel. Thus, the former ones are younger than the latter ones. It can be stated that the morphology of the main channels (shape, channel hollows, and width changes of the main channel) is determined by the tributary channels (their number, location and age).

New hybrid magnetic materials based on HDPE filled with Со and Ni nanoparticles have been prepared via the metal vapor synthesis. Properties of the metal-polymer composites have been elucidated as a function of MVS parameters and metal nature. The Faraday method has been applied to characterize the magnetic properties of the systems. The microstructure of the samples has been studied with a number of X-ray and synchrotron techniques, including XRD, EXAFS and SAXS. Core-level and valence band spectra were measured by XPS. The peak at binding energy of 282.8 eV characteristic of C-Ni bond was recorded in the C 1s spectrum. It was shown that properties of nanocomposite materials with similar compositions are determined both by the synthesis conditions and post-synthesis factors.

In this study, the effect of roasting and boiling on the yield and oxidative stability of soya bean oil was investigated. The oil was soxhlet extracted and the oxidative stability was determined by the free fatty acid value, acid value and peroxide value. The results showed that the oil yield, free fatty acid value, acid value and peroxide value were significantly affected by roasting, boiling, and the thermal treatment time. The percentage oil yield in the control oil sample was 18.51%, which increased to 20.24% and 20.73% after boiling and roasting respectively, at 40mins. The corresponding free fatty acid and the peroxide value of the control oil sample were 0.14% and 2.04 meqO₂/kg, which increased to 0.82% and 6.60 meqO₂/kg by roasting, and 0.47% and 5.62 meqO₂/kg by boiling respectively. Thus the oil yield, free fatty acid value, peroxide value, and acid value increased with increasing roasting and boiling time.
The results indicate that roasting provides a higher oil yield than boiling, but boiled oil has higher oxidative stability than roasted oil.