Among carbon nanoparticles, fullerene has been observed as a unique zero-dimensional hollow molecule. Fullerene has a high surface area and exceptional structural and physical features (optical, electronic, heat, mechanical, and others). Advancements in fullerene have been observed in the form of nanocomposites. Application of fullerene nanocomposites has been found in the membrane sector. This cutting-edge review article basically describes the potential of fullerene nanocomposite membranes for water remediation. Adding fullerene nanoparticles has been found to amend the microstructure and physical features of the nanocomposite membranes in addition to membrane porosity, selectivity, permeation, water flux, desalination, and other significant properties for water remediation. Variations in the designs of fullerene nanocomposites have resulted in greater separations between salts, desired metals, toxic metal ions, microorganisms, etc. Future investigations on ground-breaking fullerene-based membrane materials may overcome several design and performance challenges for advanced applications.

In this paper, the characteristic behavior of the disc consisting of thermoplastic composite CF/PA6 material was considered. Analysis was made by taking into account the usage areas of the materials and referring to certain temperatures between 30 ℃ and 150 ℃. Composite materials are lightweight; they show high strength. For these reasons, they are preferred in technology, especially in the aircraft and aerospace industry. With this study, the radial and tangential stresses determined within a certain temperature The temperatures were determined and compared with previous studies in the literature. According to the results obtained, it is believed that the thermoplastic composite CF/PA6 disc design can be used in engineering.

Boron and tungsten carbides, B₄C and WC, are hard materials widely used in modern technologies. Further improvement of their performance characteristics involves the development of new B₄C and WC-based and/or related composites in a nanodispersed state. This article provides a review of available literature research on B-C-W systems, which would be useful in future studies in this direction.

Bagasse fiber from sugarcane waste is used with epoxy resin to make natural composites. The raw fibers are treated chemically to improve compatibility and adherence with the epoxy polymer. It’s anticipated that epoxy resin matrix composites reinforced with bagasse particles would work as a trustworthy replacement for conventional materials utilized in the building and automobile sectors. The amount and distribution of reinforcing particles inside the matrix are two factors that impact the composite’s strength. Furthermore, the precise proportion of reinforcing elements—roughly 20–30 weight percent—into the matrix plays a critical role in providing a noticeable boost in improving the properties of the composites. This research investigates the impact of reinforcing alkali-treated bagasse and untreated bagasse powder into an epoxy matrix on aspects of mechanical and morphological characteristics. The hand layup technique is used to create alkali-treated bagasse and untreated bagasse powder-reinforced epoxy composites. Composites are designed with six levels of reinforcement weight percentages (5%, 10%, 15%, 20%, 25%, and 30%). Microstructural analysis was performed using SEM and optical microscopes to assess the cohesion and dispersion of the reinforcing particles throughout the hybrid composites’ matrix phase. With reinforcement loading up to 20 wt%, the tensile strength, impact strength, and toughness of epoxy-alkali-treated bagasse and untreated bagasse powder-reinforced composites increased. In contrast, treated bagasse epoxy composites were superior to untreated epoxy composites in terms of efficacy. The results indicate that 20 wt% alkali bagasse powder provides better mechanical properties than other combinations.

Alginate-silver nanocomposites in the form of spherical beads and films were prepared using a green approach by using the aqueous extract of Ajwa date seeds. The nanocomposites were fabricated by in situ reduction and gelation by ionotropic crosslinking using calcium ions in solution. The rich phytochemicals of the date seed extract played a dual role as a reducing and stabilizing agent in the synthesis of silver nanoparticles. The formation of silver nanoparticles was studied using UV-Vis absorption spectroscopy, and a distinct surface plasmon resonance peak at 421 nm characteristic of silver nanoparticles confirmed the green synthesis of silver nanoparticles. The morphology of the nanocomposite beads and film was compact, with an even distribution of silver nanoclusters. The catalytic property of the nanocomposite beads was evaluated for the degradation of 2-nitrophenol in the presence of sodium borohydride. The degradation followed pseudo-first-order kinetics with a rate constant of 1.40 × 10⁻³ s⁻¹ at 23 ℃ and an activation energy of 18.45 kJ mol⁻¹. The thermodynamic parameters, such as changes in enthalpy and entropy, were evaluated to be 15.22 kJ mol⁻¹ and −197.50 J mol⁻¹ K⁻¹, respectively. The nanocomposite exhibited properties against three clinically important pathogens (gram-positive and gram-negative bacteria).