It increased the demands on ground-water supplies that prolonged drought and improper maintenance of water resources. So it is necessary to evaluate ground-water resources in the hard rock terrain. In recent years, Remote-Sensing methods have been increasingly recognized as a means of obtaining crucial geoscientific data for both regional and site-specific investigations. This work aims to develop and apply integrated methods combining the information obtained by geo-hydrological field mapping and those obtained by analyzing multi-source remotely sensed data in a GIS environment for better understanding the Groundwater condition in hard rock terrain. In this study, digitally enhanced Landsat ETM+ data was used to extract information on geology, geomorphology. The Hill-Shading techniques are applied to SRTM DEM data to enhance terrain perspective views, and extract Geomorphological features and morphologically defined structures through the means of lineament analysis. A combination of Spectral information from Landsat ETM+ data plus spatial information from SRTM-DEM data is used to address the groundwater potential of alluvium, colluvium, and fractured crystalline rocks in the study area. The spatial distribution of groundwater potential zones shows regional patterns related to lithologies, lineaments, drainage systems, and landforms. High-yielding wells and springs are often related to large lineaments and corresponding structural features such as dykes. The results show that the combination of remote sensing, GIS, traditional fieldwork, and models provide a powerful tool for water resources assessment and management, and groundwater exploration planning.

Innovation management is an organizational iterative process of seeking and selecting new opportunities and ideas, implementing them, and capturing value from the results obtained. In the defense sector, due to the increasing interdependence between military capabilities and technology, countries have adopted innovation management approaches to drive the modernization of their defense industrial bases, promoting the development and integration of advanced technologies. This study presents an original systematic literature review on innovation management approaches applied to defense in developing countries. After the phases of identification and screening, 62 documents both from academic and gray literature were analyzed and categorized into 22 distinct approaches. The advantages, disadvantages, contexts, and potential applications of each approach were discussed. The findings show that the appropriate use of these approaches can strengthen the innovation capacity and technological independence of late-industrializing countries, consolidating their position in the global defense landscape and ensuring their sovereignty and continuous technological progress.

To deal with problems of traditional geographic information collection, such as low real-time, poor authenticity of the data, and unclear description of detailed areas, a design scheme of remote sensing-based geographic information system is proposed. The system mainly consists of information collection, imaging processing, data storage management, scene control and data transmission module. By use of remote sensing technology, the reflected and radiated electromagnetic waves of the target area are collected from a long distance to form an image, and the hue–intensity–saturation (HIS) transformation method is used to enhance the image definition. Weighted fusion algorithm is adopted to process the details of the image. The spatial database stores and manages the text and image data respectively, and establishes the attribute self-correlation mechanism to render the ground objects in the picture with SketchUp software. Finally, using RS422 protocol to transmit information can achieve the effect of multi-purpose, and enhance the anti-interference of the system. The experimental results show that the practical experience of the proposed system is excellent, the geographic information image presented is clear, and the edge details are clearly visible, which can provide users with effective geographic information data.

The chemical reinforcement of sandy soils is usually carried out to improve their properties and meet specific engineering requirements. Nevertheless, conventional reinforcement agents are often expensive; the process is energy-intensive and causes serious environmental issues. Therefore, developing a cost-effective, room-temperature-based method that uses recyclable chemicals is necessary. In the current study, poly (styrene-co-methyl methacrylate) (PS-PMMA) is used as a stabilizer to reinforce sandy soil. The copolymer-reinforced sand samples were prepared using the one-step bulk polymerization method at room temperature. The mechanical strength of the copolymer-reinforced sand samples depends on the ratio of the PS-PMMA copolymer to the sand. The higher the copolymer-to-sand ratio, the higher the sample’s compressive strength. The sand (70 wt.%)-PS-PMMA (30 wt.%) sample exhibited the highest compressive strength of 1900 psi. The copolymer matrix enwraps the sand particles to form a stable structure with high compressive strengths.

Broad-spectrum antibiotics, such as tetracyclines, are used to treat and manage a range of infectious disorders. Since the kidneys are the primary organs responsible for excreting tetracyclines, clinicians should refrain from prescribing them to patients who have renal failure. Tetracyclines are one of the clinical waste products of today. One of the biggest problems in the field of pollution of the environment today is the persistence of different pharmaceutical residues, drug residues, pesticides, and metal ion species of the new-generation pollutants in surfaces and groundwater. In the present work, carboxymethyl cellulose (CMC)-CuO nanoparticles (CMC-CuO NPs) were synthesized using CuO NPs within different amounts of CMC (0.5, 1.0, 1.5 and 2.0 g) at 85 °C. The synthesized nanoparticles were characterized by XRD, FT IR, SEM, and TG-DTA analysis. According to XRD and SEM, the crystallize size and morphology influenced the dosage of CMC. FT-IR analysis confines the layer of CMC to the CuO nanoparticle surface. TG-DTA results indicated that the CMC content of CMC-CuO NPs was between the range of 69% and 75% by weight. The effects of some parameters such as initial concentration, pH, adsorbent dosage, and contact time on the adsorption of tetracycline from aqueous model solutions on CMC-CuO NPs were investigated with batch studies. It was found that the removal of tetracycline was obtained about 80% with optimized parameters of 10 mg/L concentration, 180 min contact time, 5 pH, and 0.3 g/25 mL dose. The synthesized CMC-CuO NPs nanocomposite may be a promising material for the removal of tetracycline in environmental pollution and toxicology.

Studies related to the use of steel mill slag have become essential, because of the possibility of its use as a component of substrates in the production of seedlings and because this use minimizes the risk of environmental contamination, resulting from inadequate disposal. Thus, the objective of this work was to evaluate the effect of increasing levels of steel slag in substrates composed of soil with tanned bovine manure and sand, on the growth variables and the quality of “Dedo-de-moça” pepper (Capsicum baccatum L.) seedlings. A randomized block design was used with five slag concentrations (0%, 2.5%, 5%, 10% and 20%) and four repetitions. Evaluations occurred at 55 days after sowing, consisting of counting the number of leaves, measuring plant height and collar diameter, quantifying the dry mass of leaves and roots and determining the Dickson Quality Index. Regression models were fitted (P < 0.05) to treatments with increasing levels of steel slag. The addition around 10% of slag to the substrate provided the highest values of growth variables, in seedlings of Dedo-de-moça pepper.