Nowadays, our life needs more and more electricity, and our lives cannot be without electricity, which requires our power to develop more quickly. Power plants are undoubtedly the place where electricity is produced. And now most of the power plant or chemical energy can be converted into heat, and then through the heat to do power production. The boiler is the main part of the power plant. Boiler unit consists of boiler body equipment and auxiliary equipment. The main body of the boiler consists of 'pot' (soft drinks system) and 'furnace' (combustion system). Baotou thermal power plant is mainly burning gas. The gas and air are at a certain rate into the furnace burning. This can greatly reduce the pollution of the environment, but also the full use of fuel. The soda system is mainly carried out in the drum. The heat generated by the combustion system heats the water in the drum, producing steam and then pushing the steam turbine into mechanical energy and finally into electrical energy. This has a high demand for water level, water composition, and the temperature of the steam produced in the drum. The water level should have upper and lower bounds, keeping it within a certain range. Water level is too high, will affect the steam drum soda separation effect, so that the steam drum exports of saturated steam with water increased, causing damage to the turbine, will cause serious explosion. And the water level is too low, it will affect the natural circulation of the normal, serious will make the individual water pipe to form a free water, resulting in flow stagnation, resulting in local metal wall overheating and burst pipe. Water in the heating at the same time will form a lot of scale, if not the chemical treatment of water will be in the formation of scale in the drum, cleaning more difficult, so the damage to the drum. The pressure of the drum is also an important control variable, and pressure control is highly correlated with liquid level control. It is necessary to ensure the integrity of the equipment, but also to ensure safety, followed by ensuring that the process of normal operation of the drum water. This time, the design is mainly for the unit steam temperature control system design. Steam temperature is one of the important indicators of boiler operation quality. It is too high and too low will significantly affect the power plant safety and economy. If the temperature of the steam is low, it will cause the power plant to increase the heat consumption and increase the axial thrust of the turbine to cause the thrust bearing to overload, but also cause the steam turbine to increase the final steam humidity, thus reducing the efficiency of the turbine, aggravating the erosion of the blade. On the contrary, the steam temperature is too high will make the super-heater wall metal strength decreased, and even burn the high temperature of the super-heater, the steam pipe and steam turbine high-pressure part will be damaged, seriously affecting safety. The boiler temperature control system mainly includes the adjustment of the superheated steam and the reheat steam temperature. The superheated steam temperature is the highest temperature in the boiler soda system. The stability of the steam temperature is very important for the safe and economical operation of the unit. Therefore, in the boiler operation, must ensure that the steam temperature in the vicinity of the specified value, and the temperature of the super-heater tube wall does not exceed the allowable working temperature.

Coal is important basic energy and important raw materials, the development of coal industry to support the rapid development of the national economy. In the 1950s and 1960s, the proportion of coal in China's primary energy production and consumption structure accounted for 90% and 80% respectively, and the proportion of coal in 2004 was 75.6% and 67.7% respectively. In recent years, with the rapid development of fully mechanized mining equipment manufacturing technology, fully mechanized mining equipment to heavy, strong and automated, so that the reliability of the equipment is guaranteed, a strong impetus to the development of large mining technology, new round of coal mining technology revolution, the current in the East, Jincheng and other mining areas have been the first in the thick coal seam f = 1.5-5 use of large mining height fully mechanized mining equipment, to achieve the highest efficiency, the lowest cost of tons of coal. The main points of this paper are: in the production of coal enterprises to improve the competitiveness of the coal market. Conditions and conditions of coal storage conditions should be allowed to give priority to the use of large mining and mining methods.

Lithospermum extract from Lithospermum is a kind of naphthoquinone, which has good anti-ultraviolet and anti-bacterial function. In this paper, the effects of different treatment temperature, time and ratio of liquid to liquid on the UV resistance of Lithospermum erythrorhizon extract were studied. The optimum extraction conditions were as follows: extraction temperature 60 ℃, extraction time 2 h, ratio of liquid to liquid of Lithospermum and ethanol 1:11. In this paper, the anti-UV finishing of cotton fabric was carried out, and the anti-ultraviolet and whiteness of the fabric were taken as the main indexes. The optimum process of the anti-UV finishing was as follows: the impregnation temperature was 70 ℃, the immersion time was 2h, 1:40. Compared with the uncoated cotton fabric, the fabric UPF value of the fabric was improved from 12.31 to 83.25, and the anti-ultraviolet performance was excellent, and it had certain bacteriostatic effect on Bacillus subtilis and Escherichia coli.

The development of flexible, wearable electronic devices is one of the future directions of technology development. Flexible conductive materials are important supporting materials for wearable electronic devices. Polymer has excellent flexibility; it is an important way to prepare flexible conductors from polymer-based conductive composites. In this paper, the research progress of polymer-based flexible conductive composites is summarized in terms of preparation and characterization methods. The key factors to realize flexible conductors are put forward, namely, the maintenance of excellent polymer elasticity and the realization of stability. The design and preparation of the extensible conductor with high-elasticity matrix and nanofiller are introduced in detail, and the problems in the current research are summarized.

The fresh dried pollen of grape and seedless grape varieties were used as the research material. Each cultivar was stored at room temperature, 5 C, 0 C, -18 C and -40 C respectively. Sucrose 200g / L + boric acid 50mg / L + agar 8g / L as the nutrient substrate, and the comparative study on the germination and culture of the nuclear breed and the seedless cultivar. The results showed that the pollen viability decreased with the increase of storage time at different temperatures. The pollen viability decreased at -18 C and -40 , and the pollen viability decreased at the same temperature The There was a significant difference in pollen viability between different cultivars at the beginning of storage, and the pollen viability of the kernel breed was higher than that of the seedless grape.

Benzoxazine resin, a new type of phenolic resin, has many advantages, such as a strong molecular design, no small molecular release in the curing process, excellent thermal stability and mechanical properties, and a high residual carbon ratio. Thus, it is important for electronic communication industry matrix material. To meet the needs of high-frequency and high-speed communication technology for low-dielectric polymer resin, the low-dielectric modification of benzoxazine resin is of great significance to the high frequency and high-speed propagation of the signal, which attracts a wide range of materials researchers’ attention. In this paper, we review a series of studies on the low dielectric modification of benzoxazine resin in recent years, including the synthesis of new monomers, inorganic - organic hybridization, copolymerization with other resins, and low molecular weight benzoxazine resin research trends.