Synthesis of macro-mesoporous Titania (Titanium dioxide-TiO₂) nanospheres was successfully achieved using a modified template-free methodology to incorporate macroporous channels into a mesoporous TiO₂ framework to form mixed macro-mesoporous TiO₂ spheres (MMPT), which were doped with carbon dots (C-dots) to form improved nanocomposites (C-dots@MMPT). Elemental composition, surface bonding and optical properties of these nanocomposites were characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR) and ultraviolet-visible absorption spectroscopy (UV-VIS). Evaluation of photocatalytic activity for each (C-Dots@MMPT) sample was performed via degrading the Methylene Blue (MB) dye compared with bare samples (MMPT) under visible light irradiation using 300 Watt halogen lamp.

Fe3+-doped nano-TiO2 powders were prepared by sol-gel method. The photocatalytic activity of Fe3+-doped TiO2 nanoparticles was studied by using UV lamp as light source and methylene blue as degradation target. The photocatalytic activity of Fe3+-doped TiO2 was studied by degradation of 4L methylene blue solution with initial concentration of 10mg · L - 1. The results show that the photocatalytic activity of TiO2 can be improved by the addition of Fe3+. When the molar ratio of Fe3+ is 0.5-1%, the calcination temperature is 500 ℃. The photocatalytic degradation of methylene blue is the best.

The present study demonstrates the fabrication of heterogeneous ternary composite photocatalysts consisting of TiO₂, kaolinite, and cement (TKCe),which is essential to overcome the practical barriers that are inherent to currently available photocatalysts. TKCe is prepared via a cost-effective method, which involves mechanical compression and thermal activation as major fabrication steps. The clay-cement ratio primarily determines TKCe mechanical strength and photocatalytic efficiency, where TKCe with the optimum clay-cement ratio, which is 1:1, results in a uniform matrix with fewer surface defects. The composites that have a clay-cement ratio below or above the optimum ratio account for comparatively low mechanical strength and photocatalytic activity due to inhomogeneous surfaces with more defects, including particle agglomeration and cracks. The TKCe mechanical strength comes mainly from clay-TiO₂ interactions and TiO₂-cement interactions. TiO₂-cement interactions result in CaTiO₃ formation, which significantly increases matrix interactions; however, the maximum composite performance is observed at the optimum titanate level; anything above or below this level deteriorates composite performance. Over 90% degradation rates are characteristic of all TKCe, which follow pseudo-first-order kinetics in methylene blue decontamination. The highest rate constant is observed with TKCe 1-1, which is 1.57 h⁻¹ and is the highest among all the binary composite photocatalysts that were fabricated previously. The TKCe 1-1 accounts for the highest mechanical strength, which is 6.97 MPa, while the lowest is observed with TKCe 3-1, indicating that the clay-cement ratio has a direct relation to composite strength. TKCe is a potential photocatalyst that can be obtained in variable sizes and shapes, complying with real industrial wastewater treatment requirements.

A metakaolin-based geopolymer was fabricated with 5 ratios of two different nanomaterials. On the one hand, silicon carbide nanowhiskers and, on the other hand, titanium dioxide nanoparticles. Both were placed in water and received ultrasonic energy to be dispersed. The effects on mechanical properties and reaction kinetics were analyzed. Compared to the reference matrix, the results showed a tendency to increase the flexural strength. Probably due to the geometry of the SiC nanowhiskers and the pore refinement by the nano-TiO₂ particles. The calorimetry curves showed that incorporating TiO₂ nanoparticles resulted in a 92% reduction in total heat, while SiC nanowhiskers produced a 25% reduction in total heat.

Due to its physicochemical properties, nanoparticles titanium dioxide (nTiO₂) is being put into mass production and widespread applications, which inevitably results in their increasing exposure to the water body. After it entering the water body, the chemical properties of nTiO₂ can be influenced by ion compositions, ion strength and pH, which affects their ecological risk. Excess of ammonium (NH₄⁺) fertilizer has contaminated soil and water environments. In this paper, the Zeta potentials and hydrodynamic radius of nTiO₂ were studied in NH₄⁺ solution compared to those in Na⁺ solution. In addition, the sedimentation rate of nTiO₂ was also investigated. The experiment results show that high pH inhibits the sedimentation of nTiO₂. Moreover, NH₄⁺ increases the stability of nTiO₂ more than Na⁺ at the same IS, which was attributed the more negative Zeta potentials and the smaller hydraulic radius. Our results provide a theoretical basis for evaluating the ecological risk of nTiO₂ in aqueous solution containing NH₄⁺.

We studied Zeta potentials of nanoparticles titanium dioxides （nTiO₂） in different concentration of NaNO₃ and phosphate (P) solutions. In addition, the effect of flow rate on the transport of nTiO₂ in P was investigated at pH＝6.5. Experimental results show that the Zeta potential of nTiO₂ is compressed with the increasing ion concentration (IC) of NaNO₃ at pH＝6.5. The negative charge increases with the augment of P. Therefore, the high P and low NaNO3 induce the stabilization of nTiO₂ aggregates. The transport experiments suggest that the rapid flow rate is favorable for the transportability of nTiO₂ and soluble phosphate. The breakthrough transport curves (BTCs) of nTiO₂ in sand columns can be fitted well with two-site kinetic attachment model. The modeling results suggest that the values of first-order attachment rate coefficients (k₂) and detachment rate coefficients (k_2d) on site 2 and first-order attachment rate coefficients (k₁) on site 1 are responsible to the attaching efficiency of nTiO₂ on sands and their transportability.