Broad-spectrum antibiotics, such as tetracyclines, are used to treat and manage a range of infectious disorders. Since the kidneys are the primary organs responsible for excreting tetracyclines, clinicians should refrain from prescribing them to patients who have renal failure. Tetracyclines are one of the clinical waste products of today. One of the biggest problems in the field of pollution of the environment today is the persistence of different pharmaceutical residues, drug residues, pesticides, and metal ion species of the new-generation pollutants in surfaces and groundwater. In the present work, carboxymethyl cellulose (CMC)-CuO nanoparticles (CMC-CuO NPs) were synthesized using CuO NPs within different amounts of CMC (0.5, 1.0, 1.5 and 2.0 g) at 85 °C. The synthesized nanoparticles were characterized by XRD, FT IR, SEM, and TG-DTA analysis. According to XRD and SEM, the crystallize size and morphology influenced the dosage of CMC. FT-IR analysis confines the layer of CMC to the CuO nanoparticle surface. TG-DTA results indicated that the CMC content of CMC-CuO NPs was between the range of 69% and 75% by weight. The effects of some parameters such as initial concentration, pH, adsorbent dosage, and contact time on the adsorption of tetracycline from aqueous model solutions on CMC-CuO NPs were investigated with batch studies. It was found that the removal of tetracycline was obtained about 80% with optimized parameters of 10 mg/L concentration, 180 min contact time, 5 pH, and 0.3 g/25 mL dose. The synthesized CMC-CuO NPs nanocomposite may be a promising material for the removal of tetracycline in environmental pollution and toxicology.

Heat removal has become an increasingly crucial issue for microelectronic chips due to increasingly high speed and high performance. One solution is to increase the thermal conductivity of the corresponding dielectrics. However, traditional approach to adding solid heat conductive nanoparticles to polymer dielectrics led to a significant weight increase. Here we propose a dielectric polymer filled with heat conductive hollow nanoparticles to mitigate the weight gain. Our mesoscale simulation of heat conduction through this dielectric polymer composite microstructure using the phase-field spectral iterative perturbation method demonstrates the simultaneous achievement of enhanced effective thermal conductivity and the low density. It is shown that additional heat conductivity enhancement can be achieved by wrapping the hollow nanoparticles with graphene layers. The underlying mesoscale mechanism of such a microstructure design and the quantitative effect of interfacial thermal resistance will be discussed. This work is expected to stimulate future efforts to develop light-weight thermal conductive polymer nanocomposites.

Banana macropropagation in a thermal chamber is an economical technology, effective as a phytosanitary cleaning method, and efficient to enhance seedling production. The objective of this work was to evaluate the effects of corm size (CS) and benzylaminopurine (BAP) on plantain cv. Barraganete seedling proliferation in two propagation environments (PE). The treatments consisted of two levels of BAP (with and without BAP), three CS (2 ± 0.5, 4 ± 0.5 and 6 ± 0.5 kg) and two PE (thermal chamber and raised bed). The variables evaluated were sprouting time (days), multiplication rate (MT) per unit (seedlings per corm) and area (seedlings per m²). Sprouting time was significantly influenced (p < 0.05) by the PE, where the thermal chamber advanced shoot emergence by 12 days, with respect to the raised bed. MT of seedlings per corm and m², were significantly influenced (p < 0.05) by BAP × AP and TC × AP interactions, where the highest seedling production per corm occurred inside thermal chamber with BAP and 6 ± 0.5 kg corms, while seedling production per m² was higher with 2 ± 0.5 kg corms under the same thermal chamber conditions and with BAP. The main effects results reported that with BAP there were 30 and 31% increases in MT per corm and per m², respectively, relative to the treatment without BAP. Within the thermal chamber the MT per corm and per m² increased by 44% relative to the raised bed. Regarding the effect of CS, larger corms achieved higher individual MT, while smaller corms achieved higher MT per area. The use of a thermal chamber and BAP is recommended for mass production of banana seedlings through macropropagation.