This comprehensive review examines recent innovations in green technology and their impact on environmental sustainability. The study analyzes advancements in renewable energy, sustainable transportation, waste management, and green building practices. To accomplish the specific objectives of the current study, the exploration was conducted using the PRISMA guidelines in major academic databases, such as Web of Science, Scopus, IEEE Xplore, and ScienceDirect. Through a systematic literature review with a research influence mapping technique, we identified key trends, challenges, and future directions in green technology. Our aggregate findings suggest that while significant progress has been made in reducing environmental impact, barriers such as high initial costs and technological limitations persist. Hence, for the well-being of societal communities, green technology innovations and practices should be adopted more widely. By investing in sustainable practices, communities can reduce environmental degradation, improve public health, and create resilient infrastructures that support both ecological and economic stability. Green technologies, such as renewable energy sources, eco-friendly construction, efficient waste management systems, and sustainable agriculture, not only mitigate pollution but also lower greenhouse gas emissions, thereby combating climate change. Finally, the paper concludes with recommendations for policymakers and industry leaders to foster the widespread adoption of green technologies.

This paper presents a coupling of the Monte Carlo method with computational fluid dynamics (CFD) to analyze the flow channel design of an irradiated target through numerical simulations. A novel series flow channel configuration is proposed, which effectively facilitates the removal of heat generated by high-power irradiation from the target without necessitating an increase in the cooling water flow rate. The research assesses the performance of both parallel and serial cooling channels within the target, revealing that, when subjected to equivalent cooling water flow rates, the maximum temperature observed in the target employing the serial channel configuration is lower. This reduction in temperature is ascribed to the accelerated flow of cooling water within the serial channel, which subsequently elevates both the Reynolds number and the Nusselt number, leading to enhanced heat transfer efficiency. Furthermore, the maximum temperature is observed to occur further downstream, thereby circumventing areas of peak heat generation. This phenomenon arises because the cooling water traverses the target plates with the highest internal heat generation at a lower temperature when the flow channels are arranged in series, optimizing the cooling effect on these targets. However, it is crucial to note that the pressure loss associated with the serial structure is two orders of magnitude greater than that of the parallel structure, necessitating increased pump power and imposing stricter requirements on the target container and cooling water pipeline. These findings can serve as a reference for the design of the cooling channels in the target station system, particularly in light of the anticipated increase in beam power during the second phase of the China Spallation Neutron Source (CSNS Ⅱ).

Encouraging the social empowerment of persons with disabilities—also known as “people of determination” is a crucial step toward advancing equality and inclusion in our communities. Consequently, the current study aimed to identify the mechanisms for activating social empowerment for people of determination from the deaf category. Identify the most prominent mechanisms and proposals from the point of view of the deaf. The study used a social survey approach based on a questionnaire on a sample of (30) deaf males in the Kuwaiti Sports Club for the Deaf, and it is the full sample size. The study reached several results, the most important of which are: integrating deaf people with disabilities into jobs integrated into society, raising the level of cultural awareness of sign language, in addition to spreading awareness of how to deal with deaf people. The study presented some recommendations and proposals, including media focus on the deaf group, and working to hold conferences and workshops targeting the community to spread awareness about the deaf group.

This study explores the impact of technological innovations on audit transparency, objectivity, and assurance. The study employs a systematic literature review methodology, analyzing a wide range of scholarly articles, research papers, and reports to synthesize the findings. The methodology involved identifying keywords, conducting comprehensive searches in academic databases, and evaluating the selected literature. The study identifies key themes on how technological innovations impact audit practices through analysis of the literature. The impacts of technology include enhanced audit transparency through improved documentation capabilities, real-time reporting, and increased stakeholder engagement. Technological advancements bolster audit objectivity by automating repetitive tasks, facilitating advanced data analysis, and promoting standardized audit procedures. However, the analysis highlighted challenges associated with the use of technology in audits including complex technology implementation and the potential for biases. This research study contributes to the existing body of knowledge by consolidating relevant research and insights on the subject matter.

Yunnan is rich in cultural heritage, with its primitive pottery techniques coexisting with modern pottery techniques, and is known as the “Museum of Ceramic History”. Due to regional and socio-economic development factors, some folk pottery and craftsmen have faded out of sight or only circulated in a few small areas and specific environments. The study analyzes and summarizes the characteristics of Yunnan folk pottery and industry and evaluates the Yunnan folk pottery value based on the conditional valuation method. The study takes the folk pottery of the Bai nationality in Dali, Yunnan as an example and obtains the evaluation results of the purchasing motivation value of the pottery through a questionnaire survey. 45.26% of people pay for their existence value, 26.03% pay for their choice value, and 28.71% pay for their legacy value. Based on the evaluation results, the study proposes targeted activation paths for Yunnan folk pottery, including innovative development combined with new technologies, highlighting the functional characteristics of pottery, and brand building. This study will help Yunnan folk pottery find more suitable ways of protection and inheritance in the rapid development of materials and technology. This study can help inheritors gain the possibility of sustainable development and provide reference value for the activation path of other traditional folk.

On the basis of the enlightenment of international engineering education accreditation for the reform and development of higher education in China, combined with the important measures of the national “double first-class” construction, new challenges have been proposed for innovative talent cultivation among engineering majors in the context of promoting national development. These challenges also promote the reform of science-oriented courses among engineering majors. As a core mandatory course for engineering majors, biochemistry plays a crucial role in the entire educational process at universities, serving as a bridge between basic and specialized courses. To address challenges such as limited course resources, insufficient development of students’ advanced thinking and innovation skills, and overly standardized assessment methods, the bioengineering major from Guilin University of Technology restructured the biochemistry course content. A blended teaching model termed “three integrations, three stages, one sharing”, was implemented. This effort has yielded significant results, providing a research foundation for constructing an innovative talent cultivation system that is oriented toward industry needs within modern industrial colleges. It also offers valuable insights into and reference points for the cultivation of engineering talents and curriculum reform in local universities.