Different color-promoting treatments were tested on table grape cv. “Flame Seedlees” to evaluate changes on flavonoids such as anthocyanins and the residual ethylene produced. Treatments were spray-applied at the onset of veraison. The control was Ethrel at 250 ppm (ETH), Salicylic Acid at 100 ppm (AS), Melatonin at 25 ppm (MEL) and 1:1 mixtures of ETH+AS, ETH+MEL and AS+MEL. The trials were conducted in triplicate after harvest, measuring Total Soluble Solids (% TSS), total acidity (% tartaric acid), pH, residual ethylene (ppm) and anthocyanin content (mg∙cm^-2). It was found that treatments ETH, AS, MEL and ETH+AS reached 16% TSS, standing out with lower values ETH +MEL (14.27%) and AS+MEL (15.17%) (p ≤ 0.05). ETH reached 0.83 ppm of residual ethylene, while a sum effect was appreciated in ETH+AS (0.5 ppm) and ETH+MEL (0.35 ppm), but not beneficial as it did not reflect quality characteristics. Only differences (p ≤ 0.05) in anthocyanin content were recorded between ETH (0.019 mg∙cm^-2) and AS+MEL (0.003 mg∙cm^-2). The subjective color of the grape bunches in the field made it possible to relate it to the objective results of the analyses performed. This research provides commercially important information on the substitution of Ethrel by natural compounds such as AS and MEL, as they show similar effects on the quality of “Flame Seedless” table grapes. In addition, these compounds do not have an ethylene residual greater than 0.2 mg/kg.

The boom in nanotechnology over the last three decades is undeniable. Responsible for this interest in nanomaterials are mainly the nanostructured forms of carbon, since historically they were the ones that inaugurated the study of nanomaterials with the discovery of fullerenes in 1985 and carbon nanotubes in 1991. Although a variety of techniques exist to produce these materials, chemical vapor deposition (CVD) is particularly valuable as it allows the production of a wide variety of carbon nanostructures, is versatile, scalable, easy to implement and relatively low cost. This review article highlights the importance of CVD and details its principles, operating conditions and parameters, as well as its main variants. A description of the technique used to produce fullerenes, nano-ceramics, carbon nanotubes, nanospheres, graphene and others is made, emphasizing the specific parameters for each synthesis.

This work shows the results of the biosynthesis of silver nanoparticles using the microalga Chlorella sp, using growth media with different concentrations of glycerol, between 5%–20%, and different light and temperature conditions. The synthesis of nanoparticles was studied using supernatants and pellets from autotrophic, heterotrophic and mixotrophic cultures of the microalga. The presence of nanoparticles was verified by ultraviolet-visible spectroscopy and the samples showing the highest concentration of nanoparticles were characterized by scanning electron microscopy. The mixotrophic growth conditions favored the excretion of exopolymers that enhanced the reduction of silver and thus the formation of nanoparticles. The nanoparticles obtained presented predominantly ellipsoidal shape with dimensions of 108 nm × 156 nm and 87 nm × 123 nm for the reductions carried out with the supernatants of the mixotrophic cultures with 5% and 10% glycerol, respectively.

Four alloys based on niobium and containing about 33wt.%Cr, 0.4wt.C and, in atomic content equivalent to the carbon one, Ta, Ti, Hf or Zr, were elaborated by classical foundry under inert atmosphere. Their as-cast microstructures were characterized by X-ray diffraction, electron microscopy, energy dispersion spectrometry and while their room temperature hardness was specified by Vickers indentation. The microstructures are in the four cases composed of a dendritic Nb-based solid solution and of an interdendritic NbCr₂ Laves phase. Despite the MC-former behavior of Ta, Ti, Hf and Zr usually observed in nickel or cobalt-based alloys, none of the four alloys contain MC carbides. Carbon is essentially visible as graphite flakes. These alloys are brittle at room temperature and hard to machine. Indentation shows that the Vickers hardness is very high, close to 1000HV_10kg. Indentation lead to crack propagation through the niobium phase and the Laves areas. Obviously no niobium-based alloys microstructurally similar to high performance MC-strengthened nickel-based and cobalt-based can be expected. However the high temperature mechanical and chemical properties of these alloys remain to be investigated.

The importance of improving industrial transformation processes for more efficient ones is part of the current challenges. Specifically, the development of more efficient processes in the production of biofuels, where the reaction and separation processes can be intensified, is of great interest to reduce the energy consumption associated with the process. In the case of Biodiesel, the process is defined by a chemical reaction and by the components associated to the process, where the thermochemical study seeks to develop calculations for the subsequent understanding of the reaction and purification process. Thus, the analysis of the mixture of the components using the process simulator Aspen Plus V9^® unravels the thermochemical study. The UNIFAC-DMD thermodynamic method was used to estimate the binary equilibrium parameters of the reagents using the simulator. The analyzed aspects present the behavior of the components in different temperature conditions, the azeotropic behavior and the determined thermochemical conditions.