This study delves into the complex flow dynamics of magnetized bioconvective Ellis nanofluids, highlighting the critical roles of viscous dissipation and activation energy. By employing a MATLAB solver to tackle the boundary value problem, the research offers a thorough exploration of how these factors, along with oxytactic microorganism’s mobility, shape fluid behavior in magnetized systems. Our findings demonstrate that an increase in the magnetization factor  leads to a decrease in both velocity and temperature due to enhanced interparticle resistance from the Lorentz force. Additionally, streamline analysis reveals that higher mixed convection parameters  intensify flow concentration near surfaces, while increased slip parameters reduce shear stress and boundary layer thickness. Although isotherm analysis shows that higher Ellis fluid parameters enhance heat conduction, with greater porosity values promoting efficient thermal dissipation. These insights significantly advance our understanding of nanofluid dynamics, with promising implications for bioengineering and materials science, setting the stage for future research in this field.

This paper concerns a miniature gasifier fed with a constant ambient-pressure flow of air to study the pyrolysis and subsequent combustion stage of a single wood pellet at T = 800 ℃. The alkali release and the concentration of simple gases were recorded simultaneously using an improved alkali surface ionisation detector and a mass spectrometer in time steps of 1 s and 1.2 s, respectively. It showed alkali release during both stages. During combustion, the MS data showed almost complete oxidation of the charred pellet to CO₂. The derived alkali release, “O₂ consumed”, and “CO₂ produced” conversion rates all indicated very similar temporal growth and coalescence features with respect to the varying char pore surface area underlying the original random pore model of Bhatia and Perlmutter. But, also large, rapid signal accelerations near the end and marked peak-tails with O₂ and CO₂ after that, but not with the alkali release data. The latter features appear indicative of alkali–deprived char attributable to the preceding pyrolysis with flowing air. Except for the peak-tails, all other features were reproduced well with the modified model equations of Struis et al. and the parameter values resembled closely those reported for fir charcoal gasified with CO₂ at T = 800 ℃.

The present research is on the propagation of Rayleigh waves in a homogenous thermoelastic solid half-space by considering the compact form of six different theories of thermoelasticity. The medium is subjected to an insulated boundary surface that is free from normal stress, tangential stress, and a temperature gradient normal to the surface. After developing a mathematical model, a dispersion equation is obtained with irrational terms. To apply the algebraic method, this equation must be converted into a rational polynomial equation. From this, only those roots are filtered out, which has satisfied both of the above equations for the propagation of waves decaying with depth. With the help of these roots, different characteristics are computed numerically, like phase velocity, attenuation coefficient, and path of particles. Various particular cases are compared graphically by using phase velocity and attenuation coefficient. The elliptic path of surface particles in Rayleigh wave propagation is also presented for the different theories using physical constants of copper material for different depths and thermal conductivity.

The present work conducts a comprehensive thermodynamic analysis of a 150 MW_e Integrated Gasification Combined Cycle (IGCC) using Indian coal as the fuel source. The plant layout is modelled and simulated using the “Cycle-Tempo” software. In this study, an innovative approach is employed where the gasifier's bed material is heated by circulating hot water through pipes submerged within the bed. The analysis reveals that increasing the external heat supplied to the gasifier enhances the hydrogen (H₂) content in the syngas, improving both its heating value and cold gas efficiency. Additionally, this increase in external heat favourably impacts the Steam-Methane reforming reaction, boosting the H₂/CH₄ ratio. The thermodynamic results show that the plant achieves an energy efficiency of 44.17% and an exergy efficiency of 40.43%. The study also identifies the condenser as the primary source of energy loss, while the combustor experiences the greatest exergy loss.

This paper presents a coupling of the Monte Carlo method with computational fluid dynamics (CFD) to analyze the flow channel design of an irradiated target through numerical simulations. A novel series flow channel configuration is proposed, which effectively facilitates the removal of heat generated by high-power irradiation from the target without necessitating an increase in the cooling water flow rate. The research assesses the performance of both parallel and serial cooling channels within the target, revealing that, when subjected to equivalent cooling water flow rates, the maximum temperature observed in the target employing the serial channel configuration is lower. This reduction in temperature is ascribed to the accelerated flow of cooling water within the serial channel, which subsequently elevates both the Reynolds number and the Nusselt number, leading to enhanced heat transfer efficiency. Furthermore, the maximum temperature is observed to occur further downstream, thereby circumventing areas of peak heat generation. This phenomenon arises because the cooling water traverses the target plates with the highest internal heat generation at a lower temperature when the flow channels are arranged in series, optimizing the cooling effect on these targets. However, it is crucial to note that the pressure loss associated with the serial structure is two orders of magnitude greater than that of the parallel structure, necessitating increased pump power and imposing stricter requirements on the target container and cooling water pipeline. These findings can serve as a reference for the design of the cooling channels in the target station system, particularly in light of the anticipated increase in beam power during the second phase of the China Spallation Neutron Source (CSNS Ⅱ).